APF Polyurethane 100 VOC Satin - Aliphatic Polyurethane Topcoat Product Overview APF Polyurethane 100 is a two-component, high-solids aliphatic polyurethane coating engineered for high-performance flooring and protective coating applications. This topcoat delivers a hard, flexible film with excellent impact resistance, abrasion resistance, and long-term durability in both interior and exterior environments. Formulated with an integral UV additive, APF Polyurethane 100 offers excellent performance under sunlight and strong artificial light. The high-gloss finish is easy to clean and resists staining, chemical attack, and graffiti. A curing accelerator is available for faster turnaround times and is required for the satin finish option. Key Features High-Gloss & Satin Options: Provides superior appearance and protection in both finishes. UV-Stable & Weather Resistant: Performs reliably in outdoor and high-light environments. High Impact & Scratch Resistance: Ideal for heavy-duty commercial floors. Fuel & Chemical Resistant: Withstands exposure to harsh substances. Flexible Yet Hard Surface: Balances durability with application versatility. Optional Curing Accelerator: Speeds up dry times when needed. Recommended Uses Topcoat for color quartz and vinyl flake flooring systems Automotive repair shops and garages Aircraft hangars and service bays Clean rooms and hygienic spaces Interior or exterior wall surfaces requiring graffiti resistance Installation Notes APF Polyurethane 100 should be applied over a properly prepared and cured base system using a roller or squeegee. The product is available in both gloss and satin finishes. When using the satin finish, a curing accelerator must be added. For optimal performance, follow APF's technical data sheet regarding spread rate, cure time, and surface preparation requirements.  

APF Polyurethane 250 Gloss– Acrylic Urethane Primer & Sealer for Concrete Product Overview APF Polyurethane 250 Gloss is a two-component, low-viscosity acrylic urethane designed for use as a primer or sealer over concrete, architectural surfaces, and decorative finishes. This product offers superior penetration and adhesion to minimally profiled concrete thanks to its unique blend of solvents and adhesion promoters. UV stable and fast-curing, it can be used in both interior and exterior applications and re-coated with either water-based or solvent-based polyurethanes.  As a finish coat, APF Polyurethane 250 delivers a hard, Gloss surface with excellent stain resistance, Satin retention, and easy cleanability. It outperforms traditional solvent-based acrylic sealers and is available in a satin finish.  Key Features Excellent Penetration & Adhesion: Bonds well to low-profile concrete and difficult substrates. UV Stable & Fast Curing: Suitable for outdoor use with rapid dry and recoat times. Color Enhancement: Improves appearance over acid-stained and integrally colored concrete. Stain & Chemical Resistant: Resists tire marking, graffiti, fuels, and many common chemicals. Re-Coatable: Compatible with both water-based and solvent-based polyurethane topcoats. Low VOC Option Available: Meets air quality regulations for restricted regions. Recommended Uses Primer for Color Quartz and Vinyl Flake Systems Topcoat for Armor-Rez Concrete Grind & Seal applications Concrete and acid-stained surfaces Retail stores, restaurants, and commercial floors Warehouses and aircraft hangars Automotive service areas and showrooms Installation Notes APF Polyurethane 250 Gloss should be applied to clean, dry, properly prepared surfaces using a roller or airless sprayer. When sealing over acid-stained or integrally colored concrete, ensure adequate ventilation and monitor surface temperatures. This product may also be used as a tie coat over hard-to-bond coatings such as polyester urethane. For best results, follow APF’s application guidelines for spread rates and cure times.  

AQUALAB Pure Gloss | Water Based Urethane Epoxy Topcoat Product Overview AQUALAB Pure Gloss is a high performance, aliphatic water based urethane topcoat engineered to provide a professional grade protective shield over epoxy flooring. This two component (5 to 1) system delivers superior chemical resistance, elite abrasion resistance, and long term UV protection while maintaining a low odor application. This is the definitive choice for installers who need to protect warehouse and light duty commercial epoxy floors from premature wear, staining, and UV damage. The Aliphatic Advantage: Why Use a Urethane? While epoxy provides the structural build and "pop" for decorative floors, it is naturally susceptible to micro scratches and chemical staining. AQUALAB Pure Gloss adds an aliphatic urethane layer that is significantly harder and more resilient than epoxy. This is why most professional systems use a urethane or polyaspartic topcoat instead of leaving epoxy exposed. This results in: Extreme Scratch Resistance: Drastically reduces the "dulling" effect of foot traffic. UV Shielding: Unlike standard epoxy, this topcoat will not yellow and helps slow down the ambering of the epoxy layers beneath it. Stain Protection: Creates a non-porous surface that is much easier to clean and maintain in residential or commercial settings. Finish Options Gloss: Delivers a high-shine, glass like finish that maximizes color depth. Satin: Provides a refined, low-sheen look that hides surface imperfections and dust more effectively. Frequently Asked Questions Is this better than using epoxy as a topcoat?Yes. Aliphatic urethane topcoats provide significantly better chemical resistance, scratch resistance, and long term cleanability compared to standard epoxy alone. Does this product yellow?No. AQUALAB is non yellowing and contains UV inhibitors that help protect the underlying epoxy layers from direct sunlight. Can this be used indoors?Yes. The low odor, water based formulation is specifically designed for interior and occupied environments where solvent smells are not permitted. How many coats should I apply?We recommend two coats for the best durability and to ensure a perfectly uniform aesthetic finish across the entire floor. Can this be used over any epoxy?It is designed for use over properly prepared epoxy systems. If you are applying it over a different brand, we recommend a small adhesion test first. What is the mix ratio?The mix ratio is 5 parts Part A to 1 part Part B. Ensure you mix thoroughly for 2 to 3 minutes before application. What is the coverage rate?Coverage typically ranges from 500 to 600 square feet per kit on smooth surfaces and 400 to 500 square feet on partial flake epoxy floors. Can I add water to the mixture?No. Do not add water or solvents to the mixture. AQUALAB is formulated to be used exactly as it is packaged. How soon can I walk on the floor?The floor is typically ready for foot traffic after 24 hours of cure time at standard room temperatures. What is the best way to apply AQUALAB?Use the "dip and roll" method with a high-quality lint-free roller. This product is designed for dip and roll application rather than ribbon pour methods used with some other coatings.

Labfast 85 (+) Low Odor One say Floor Polyaspartic Labfast 85 (+) Low Odor is a high performance, 85 percent solids polyaspartic coating designed for fast curing, low odor installations, and rapid return to service. This professional grade, two component (1 to 1) system is uniquely engineered to serve as both a pigmented base coat and a high gloss clear topcoat using a common hardener. This system is built for one day floor installations where speed, durability, and low odor are non-negotiable requirements. Where This Product Fits in Your System One Day Garage Floors: Go from prep to topcoat in a single day. Occupied Interiors: Low odor formulation makes it ideal for retail, offices, and residential basements. UV Stable Topcoat: Non yellowing protection for interior and exterior decorative flake or quartz systems. Cold Weather Installs: Maintains a reliable cure even in temperatures where epoxy systems would fail. Key Advantages Low Odor Formula: Specifically designed for sensitive environments and occupied buildings. (+) Extended Working Time: Provides approximately 25 minutes of "open time" for superior application control and better leveling. Rapid Return to Service: Tack free in as little as 45 to 60 minutes depending on humidity and temperature. Extreme Durability: 85 percent solids content provides excellent abrasion and chemical resistance. Common Hardener: Simplifies inventory by using the same Part B for both clear and pigmented layers. Weather Resistant: 100 percent UV stable for long term exterior performance without ambering. System Flexibility This product can be used in two coat or three coat systems depending on the application. It works as both a pigmented base coat and a clear protective topcoat using the same hardener, simplifying inventory and installation. For the pigmented base coat, simply add Labsurface Universal Pigment Pods to the clear Labfast 85 (+) Part A. For decorative systems, we recommend using vinyl flakes to build a full broadcast or partial broadcast floor system. Technical Performance Snapshot Property Value Mix Ratio 1 Part A to 1 Part B Solids Content 85 Percent Working Time Approximately 25 Minutes Tack Free Time 45 to 90 Minutes Traffic Ready 24 Hours (Vehicular) Frequently Asked Questions What makes the (+) version different from standard polyaspartics?The (+) version is engineered with a slower cure rate, giving the installer about 25 minutes of working time. This reduces the risk of roller marks and allows for better leveling on larger floors. Can I really complete a floor in one day?Yes. Because it is tack free so quickly, you can apply your base coat, broadcast your flakes, scrape, and topcoat all within a 6 to 8 hour window. Does "Low Odor" mean no odor?It has a significantly lower odor profile than traditional solvent based polyaspartics, making it much safer and more pleasant for interior residential and commercial work. Is this suitable for outdoor use?Absolutely. It is 100 percent UV stable and will not yellow, chalk, or peel when exposed to direct sunlight. Can this be used as both a base coat and topcoat?Yes. You use the pigmented Part A (created using Universal Pigment Pods) for your base coat and the clear Part A for your topcoat, both utilizing the exact same Part B hardener. How many square feet does a gallon cover?Coverage typically ranges from 125 to 200 square feet per gallon depending on surface porosity and whether it is being used as a base coat or topcoat. What is the best temperature for application?It can be applied in temperatures ranging from 20°F to 85°F. Note that the material will cure much faster in high heat and high humidity. Is it resistant to hot tire pickup?Yes. Once fully cured, Labfast 85 (+) is highly resistant to hot tire staining and chemical spills like oil or gasoline. Do I need to prime the concrete first?For most standard garage applications, this can be applied directly to mechanically profiled concrete (CSP 2 or 3). On very porous slabs, a primer may be beneficial. What happens if I wait too long between coats?If you wait longer than 24 hours to apply your next coat, you must mechanically sand the surface to ensure a proper bond.

LABFAST 85 PRO Polyaspartic | High Quality Budget Floor Coating LABFAST 85 PRO is a high solids, budget friendly polyaspartic coating designed to deliver professional grade performance and rapid return to service without the premium price tag. This professional grade (1 to 1) system allows installers to maximize profitability while providing a durable, high gloss finish that rivals more expensive formulations. This is the smart choice when you need a reliable polyaspartic system that performs at a high level while keeping your material costs under control. Elite Efficiency: Advanced Opacity Technology Even at a budget friendly price point, LABFAST 85 PRO features our Advanced Opacity Technology. This system reduces chip repulsion during the broadcast phase, ensuring your flakes stay where you put them. For the high volume installer, this means better coverage with less waste and a more consistent aesthetic across every square foot. Key Advantages Maximum Profitability: High quality performance at a price point that protects your margins. Advanced Opacity Technology: Reduces chip repulsion for superior flake broadcast efficiency. 85 Percent Solids: High film build with excellent chemical and abrasion resistance. UV Stable & Non Yellowing: 100 percent non yellowing formula suitable for both interior and exterior applications. One Day Installation: Fast cure times allow you to prep, base, and topcoat in a single shift. Common Hardener: Simplifies inventory by using the same Part B for clear and pigmented layers. System Flexibility LABFAST 85 PRO is designed to be the backbone of your flake floor business. To achieve a professional decorative finish, follow these system steps: Pigmented Base Coat: Add Labsurface Universal Pigment Pods to the clear LABFAST 85 PRO Part A. The Broadcast: Achieve a seamless decorative look using our Multi Color Flakes. Clear Topcoat: Apply a final layer of clear LABFAST 85 PRO for a high gloss, UV protected shield. Technical Performance Snapshot Property Value Mix Ratio 1 Part A to 1 Part B Tack Free Time 55 to 60 Minutes Working Time 25 Minutes Application Temp -22°F to 86°F Frequently Asked Questions Is this a lower quality polyaspartic because it costs less?No. This is a high solids, high performance system. We have optimized the formulation to deliver the core strengths installers need—UV stability, fast cure, and durability—while keeping it accessible for high volume projects. Can I complete a floor in one day?Yes. LABFAST 85 PRO is engineered for fast turnaround. You can typically apply the base coat and topcoat within a single day window. What does Advanced Opacity Technology do?It prevents flakes from "diving" or being pushed away by the resin during broadcast. This results in more even flake distribution and saves you material by improving coverage efficiency. Can this be used outdoors?Yes. It is 100 percent UV stable, meaning it will not yellow, chalk, or peel when exposed to direct sunlight on patios or walkways. How many square feet does a kit cover?For full flake floors, a kit typically covers 266 to 300 square feet. For smooth floors, coverage increases to approximately 266 to 330 square feet per kit. Is this resistant to hot tires?Yes. LABFAST 85 PRO provides excellent resistance to hot tire pickup, making it a reliable choice for residential garage floors. Does it use a common hardener?Yes. You use the same Part B hardener for both the base coat and the topcoat, which simplifies your setup and inventory management. What is the working time?You have approximately 25 minutes of working time at standard temperatures to apply and back roll the material. Is it low odor?Yes, it is formulated to have a more manageable odor profile than traditional solvent-heavy polyaspartics, making it suitable for interior use. Can I apply this in cold weather?Absolutely. Like our other professional polyaspartics, this can be applied in temperatures as low as -22°F.

LABFAST Low Odor 85 XT Polyaspartic Floor Coating LABFAST Low Odor 85 XT is a high solids, low odor polyaspartic coating engineered for installers who demand maximum control and superior flake broadcast efficiency. This professional grade (1 to 1) system utilizes Advanced Opacity Technology to provide better coverage and a more consistent finish in both residential and commercial environments. This system is specifically designed for one day flake floor installations where speed, appearance, and material efficiency are the top priorities. The XT Advantage: Advanced Opacity Technology What sets the 85 XT apart is its ability to reduce chip repulsion. In standard systems, flakes can "migrate" or be pushed away by the resin, leading to uneven coverage. LABFAST 85 XT keeps the flakes exactly where they belong, resulting in: Better Broadcast Coverage: Improved flake distribution with less effort. Up to 15 Percent Less Topcoat Usage: Because the base coat lays flatter and holds flakes better, you use significantly less clear topcoat to achieve a smooth finish. Superior Opacity: Hides concrete imperfections more effectively than standard polyaspartics. XT Version Performance Specs The XT version is designed for installers who need maximum "open time" to ensure a perfect finish without the material setting up too fast. Working Time: Up to 30 minutes of application control. Tack Free: Approximately 90 minutes. Application Window: Operates in extreme temperatures from -22°F to 86°F. UV Stable: 100 percent non yellowing for interior and exterior use. System Flexibility This system simplifies your inventory by using a common hardener for both the base coat and topcoat layers. For a professional decorative finish, follow these system steps: Pigmented Base Coat: Add Labsurface Universal Pigment Pods to the clear LABFAST 85 XT Part A. The Broadcast: Use our high-quality Multi Color Flakes to achieve a full or partial broadcast decorative look. Clear Topcoat: Use the clear LABFAST 85 XT with the same Part B hardener for a seamless, high-gloss protective finish. Frequently Asked Questions What makes this different from standard polyaspartics?This system uses Advanced Opacity Technology to improve flake coverage and reduce chip repulsion. This results in a better looking floor and uses up to 15 percent less topcoat material. What does the XT version mean?The XT version offers our longest working time (up to 30 minutes), giving installers more control and reducing the risk of roller marks compared to faster curing systems. Can I complete a floor in one day?Yes. Even with the extended working time, the system is designed for same day installation, allowing you to walk on the floor within hours of completion. Is this suitable for indoor use?Yes. The low odor formulation is engineered for interior environments and occupied buildings where solvent smells are a concern. Can this be used outdoors?Yes. It is fully UV stable and will not yellow, chalk, or peel when exposed to direct sunlight. Does it use the same hardener for both coats?Yes. You use the same Part B hardener for both your pigmented base coat and your clear topcoat layer. How much topcoat will I really save?Because the flakes lay flatter in the XT base coat, most installers see a 10 to 15 percent reduction in the amount of clear topcoat needed to reach a smooth finish. What is the mix ratio?The mix ratio is a simple 1 to 1 by volume, making it easy to measure and mix on site. What is the lowest temperature I can apply this in?LABFAST 85 XT is an incredible cold weather performer and can be applied in temperatures as low as -22°F. Is it resistant to hot tires?Yes. Like all our professional polyaspartics, once fully cured, it is highly resistant to hot tire pickup and chemical staining.

LABFENDER Aliphatic Polyurethane | Heavy Duty Floor Protection Topcoat Product Overview LABFENDER is a high solids, low VOC aliphatic polyurethane topcoat engineered for maximum durability in demanding environments. Designed to be applied over epoxy and polyaspartic systems, it provides exceptional abrasion resistance, superior chemical protection, and long term UV stability. This is the topcoat used when standard systems are not enough and long term performance under heavy traffic is required. LABFENDER significantly reduces wear from foot traffic, forklifts, and rolling equipment while protecting against staining, chemical exposure, and plasticizer transfer. Key Advantages Extreme Abrasion Resistance: Designed for heavy traffic and industrial use Superior Chemical Protection: Up to 60 times more resistant to plasticizer transfer (common cause of staining and softening in coatings) UV Stable: Non yellowing and protects underlying coatings High Solids Formulation: Strong, dense protective layer Low VOC: Suitable for regulated environments Long Working Time: Allows efficient installation over large areas Improved Cleanability: Resists dirt penetration and surface staining Where This Product Is Used Warehouses and manufacturing facilities Forklift and heavy equipment traffic areas Automotive shops and service centers Commercial kitchens and food processing plants Hospitals, labs, and clean environments Flake, quartz, and metallic flooring systems Surface Preparation Requirements LABFENDER is not designed for direct application to concrete. Apply only over epoxy or polyaspartic systems No prep required if within recoat window If outside recoat window, sand to a uniform dull finish Vacuum thoroughly and wipe clean before application Critical Mixing Instructions Mixing errors are one of the most common causes of failure with this product. Follow these instructions carefully. 3 Part Mix (Recommended) Ratio: 4 Parts A to 1 Part B plus 3 lbs Aluminum Oxide (Part C) Pre-mix Part A for 1 minute Add Part B and mix for 3 minutes at low speed (300–450 RPM) Reverse mixer direction for final 90 seconds Scrape sides and bottom of container thoroughly Add Aluminum Oxide slowly and mix an additional 2–3 minutes Recommended dosage: 3 lbs aluminum oxide per 1 gallon kit 2 Part Mix (Smooth Systems) Ratio: 4 Parts A to 1 Part B Follow same mixing procedure without adding aluminum oxide Use this method for smooth floor finishes Do not add solvents. Ensure mixing container is clean. Application Guidelines Apply between 50°F and 86°F with humidity below 80% Turn off ventilation and airflow during application Block wind when applying outdoors Apply using a roller or approved method with consistent coverage to maintain a uniform finish Why Installers Choose LABFENDER When floors are exposed to constant traffic, heavy loads, or chemical exposure, standard topcoats can wear down quickly. LABFENDER provides a higher level of protection that helps maintain the appearance and performance of the entire system over time. This is the solution for long term durability in high demand environments. Frequently Asked Questions Can I apply this directly to concrete?No. This product is designed as a protective topcoat over epoxy or polyaspartic systems. Do I need to add aluminum oxide?It is recommended for flake and quartz systems to improve durability and slip resistance. What happens if I mix it incorrectly?Improper mixing can lead to soft spots, poor curing, or complete coating failure. Follow mixing instructions exactly. Is this suitable for heavy traffic areas?Yes. It is specifically designed for high traffic, industrial, and forklift environments. Does this product yellow?No. It is UV stable and will not yellow over time.

LABSHIELD ECO Low Odor Polyaspartic | 100% Solids Ultra Fast Set  Product Overview LABSHIELD ECO Ultra Fast Set is a premium, 100% solids polyaspartic floor coating engineered for environments where odor control is just as important as durability. Unlike traditional high performance coatings that emit harsh chemical smells, LABSHIELD ECO is virtually odor free, making it the definitive choice for indoor residential, commercial, and institutional projects. This two component system is designed for high speed flake installations and rapid return to service. Featuring Advanced Opacity Technology, it reduces chip repulsion to ensure your flakes stay where you put them, resulting in a more uniform finish with less wasted material. The Indoor Advantage: Because it is solvent free and odorless, LABSHIELD ECO can be installed in basements, occupied offices, schools, and hospitals without the need for complex ventilation or building evacuations. It provides a massive build without the toxic solvent load found in cheaper coatings. Why Contractors Choose LABSHIELD ECO Virtually Odorless: Ideal for interior residential use and occupied commercial spaces. 100% Solids Formulation: Strong build with zero solvent load and no toxic fumes. Advanced Opacity Technology: Maximizes flake broadcast coverage and minimizes chip repulsion. Ultra Fast Cure: Perfect for one day floor systems and immediate return to service. Interior and Exterior Stability: UV stable and non yellowing even in direct sunlight. Cold Weather Installation: Capable of curing in temperatures as low as -22 degrees. Industrial Resistance: Elite protection against mechanical wear and chemical exposure. Technical Performance Snapshot Property Value Mix Ratio 2 Parts A to 1 Part B Working Time Approximately 15 minutes Tack Free Approximately 70 minutes Foot Traffic 24 hours Application Temp -22°F to 86°F Where This Product Fits in Your System Pigmented Base Coat: Designed for flake and quartz broadcast systems. Clear Topcoat: Used as the protective finish coat over broadcast floors. Protective Clear Coat Over Epoxy: Can also be used to protect epoxy while slowing yellowing over time. Important: Colored LABSHIELD ECO is designed strictly as a base coat and should be covered with an aggregate system such as multi color flakes or quartz. Surface Preparation Concrete must be clean, dry, and free of grease, oil, paint, and contaminants. Concrete should be cured for at least 28 days with moisture content below 4%. Surface should be mechanically prepared to a minimum CSP 2 or greater. All fibers on fiber reinforced concrete must be removed before coating. Mixing Instructions Pre mix Part A at low speed until color is uniform. Combine 2 parts Part A with 1 part Part B in a clean container. Mix for a full 3 minutes at 300 to 450 RPM. Reverse mixer direction after 90 seconds and scrape sides and bottom thoroughly. Mix only what you can apply within the 15 minute working time. Frequently Asked Questions Is this polyaspartic really low odor?Yes. LABSHIELD ECO is 100% solids and solvent free, meaning it does not have the harsh chemical smell associated with traditional polyaspartic coatings. Can I use this for indoor basement floors?Absolutely. This is the preferred choice for basements and residential interiors because it won't off gas smells into the home through the HVAC system. Does it yellow in the sun?No. It is a highly UV stable aliphatic system, making it suitable for both interior and exterior projects like patios and pool decks. Can I use the colored version as a finished floor?No. The colored version is designed only as a base coat and must be covered with flakes, quartz, or another approved finish layer.

LABSHIELD ECO Standard | Low Odor Polyaspartic with Extended Flow Product Overview LABSHIELD ECO Standard delivers the elite durability of a 100% solids polyaspartic with a critical advantage: extended working time. Engineered for installers who refuse to rush, this virtually odorless system provides a generous 25 minute window to ensure perfect flake distribution and a seamless finish on larger or more complex floor layouts. By utilizing Advanced Opacity Technology, LABSHIELD ECO eliminates the common chip repulsion issues found in inferior resins. This ensures your broadcast remains dense and uniform, creating a high end decorative finish with significantly less effort and material waste. The Indoor Advantage: Solvent free and completely odorless, the Standard formulation is the professional choice for basements, hospitals, and occupied retail spaces. You get industrial grade protection without the chemical fumes that typical polyaspartics off gas into HVAC systems. Why Professionals Choose LABSHIELD ECO Standard 25 Minute Working Window: Perfect for larger residential garages and commercial slabs where faster systems cure too quickly. Virtually Odorless: Safe for use in occupied buildings and homes without solvent migration. 100% Solids Chemistry: Provides a massive, dense film build with zero shrinkage and no toxic load. Superior Flow and Leveling: The extended open time allows the resin to settle perfectly, eliminating roller marks. UV Stable Performance: Aliphatic chemistry ensures your floor will not yellow or amber in interior or exterior applications. Extreme Chemical Resistance: Guards against salts, oils, and automotive fluids in demanding environments. Technical Performance Snapshot Property Value Mix Ratio 2 Parts A to 1 Part B Working Time Approximately 25 minutes Tack Free State Approximately 3 to 4 hours Foot Traffic Ready 24 hours Application Temp -22°F to 86°F Installation and Mixing Surface Prep: Concrete must be clean and mechanically profiled to a CSP 2. Moisture must be below 4%. Mixing: Combine 2 parts A with 1 part B. Mix for 3 minutes at low speed (300 to 450 RPM). Scrape sides and reverse direction halfway through. System Placement: Pour in ribbons and spread with a squeegee followed by a multi directional back roll. Frequently Asked Questions When should I use the Standard version instead of Ultra Fast?Standard is ideal for larger projects or solo installers who need more time to manage a wet edge and broadcast flakes without the resin tacking up prematurely. Is this safe for indoor basement projects?Yes. Because it is 100% solids and solvent free, it is virtually odorless and won't travel through your home or building ventilation system. Does it yellow in the sun?No. It is a highly UV stable aliphatic system, making it suitable for both interior and exterior projects like patios and pool decks.

Nukote Quick Seal Quick Seal is a fast-drying, solvent based, water repellent sealer designed to enhance the surface and to protect stone, concrete & masonry surfaces from nature’s destructive forces, providing a long lasting barrier which exhibits superior resistance to water, mold, airborne dust and dirt, alkali, freeze/thaw damage and spills. As well as a one step stain and seal by adding acetone based dyes into the sealer. Nukote Quick Seal Features and Benefits Stain and water repellant Very fast drying Breathable Can be used on most Natural and Artificial Stone, Concrete, and Masonry Products Breathable Penetrate the surface of the substrate Enhances and deepens natural colors of substrate Repel moisture, stains and mold from within the substrate Long-lasting, easy to clean Reduced maintenance costs Protects most Natural and Artificial Stone, Concrete, and Masonry Products against moisture, stains, dirt, mold Nukote Quick Seal Typical Uses Protects substrates against Moisture, stains, dirt, mold and more Enhance any compatible surface Suitable for most Natural and Artificial Stone, Concrete, and Masonry Products Suitable sealer under T2 Topcoat Gloss Nukote Quick Seal Coverage Rate Smooth Concrete 500-600 Broom Finish Concrete 350-450 Porous Concrete 150-250 Split Face Block 200-250 Fluted Block 200-250 Concrete Block 200-250 Clay Brick 150-300 Stucco 250-300 Sandstone, Limestone 250-300 Flagstone, Concrete Pavers 250-300

Premera Odor Block: Professional Odor Control Additive for Epoxy & Coatings What is Premera Odor Block? Premera Odor Block is a professional-grade, easy-to-use liquid additive engineered to neutralize and reduce strong chemical fumes during the installation of epoxy, urethane, and specialty coating systems. Designed specifically for contractors, it integrates seamlessly into your workflow to improve air quality in enclosed or occupied spaces without compromising the performance of your coating.Key Benefits for Coating Professionals Zero Impact on Performance: Formulated to reduce smell without altering the coating’s cure time, leveling, flow, or final aesthetic appearance. Simple Implementation: The straightforward mix ratio eliminates guesswork and prevents production slowdowns. Occupant-Friendly: The practical solution for completing installations comfortably in environments sensitive to strong chemical odors. Broad Compatibility: Specifically optimized to integrate directly into compatible Premera product systems. Optimal Use Cases and Applications Strong coating odors can create significant issues in populated environments. Premera Odor Block is the ideal additive for contractors working in: Residential Properties: Garages, basements, and interior living spaces. Commercial & Retail: Active shopping centers, storefronts, and showrooms. Offices & Workspaces: Occupied corporate buildings and medical facilities. Enclosed Areas: Any poorly ventilated space where fume mitigation is a priority. Technical Specifications & Application Instructions Feature Specification Product Type Odor-reducing coating additive Compatible Systems Epoxy, urethane, specialty coatings Optimized Premera Products Premera T2 MCM, Fusion Primer, Crystal Densifier Mix Ratio 1 container of Odor Block per 1 gallon of coating Effect on Cure Time None Effect on Final Finish None   How to Mix: Simply add one container of Premera Odor Block for every one gallon of your compatible coating product. Stir the additive directly into the mixture according to your standard system guidelines before application. Frequently Asked Questions (FAQ) What is Premera Odor Block used for? Premera Odor Block is used by professional contractors to significantly reduce strong chemical odors and fumes during the installation of epoxy, urethane, and specialty coating systems, particularly in enclosed or occupied spaces. Does Odor Block affect the performance of the epoxy or coating? No. Premera Odor Block is scientifically formulated to neutralize odors without changing the cure time, flow, leveling, or the finished result of your coating system. What products can Premera Odor Block be used with? While it is compatible with many epoxy and urethane systems, it is heavily optimized for use with Premera products, including Premera T2 MCM, Fusion Primer, and Crystal Densifier. How do you mix Premera Odor Block into epoxy? The standard mix ratio is incredibly straightforward: add one container of Premera Odor Block per one gallon of the coating product being used. Why should contractors use an odor-reducing additive? Contractors use odor-reducing additives to maintain a comfortable, professional environment, reduce complaints from clients or neighbors, and safely complete installations in sensitive spaces like residential homes, hospitals, and active retail stores.  

One Stop Epoxy Urethane WB | Interior Topcoat for Epoxy Floors One Stop Epoxy Urethane WB is a professional grade water based urethane designed for high performance interior flooring. While modern coatings like Slow Go Polyaspartic and Premera T2 offer advanced speed and clarity, this Water Based Urethane remains the premier choice for occupied residential and commercial spaces where low odor and cost efficiency are the top priorities. Engineered for installers who need a forgiving application window without the heavy chemical smell typical of high solids polyaspartics, this urethane provides a durable, reliable finish for metallic, solid color, and flake systems. It is the perfect balance for projects that demand a professional interior result on a budget conscious scale. Choose this topcoat when low odor and application control are paramount for your interior environment. Where This Product Fits in Your System This protective finish is designed to lock in your decorative system and provide reliable wear resistance: Topcoat for Metallic Dream Epoxy Seal coat for solid color epoxy floors Topcoat for partial flake systems Protective finish over 100% solids epoxy Grind and seal applications directly on concrete Pro Note: While this urethane is highly durable for standard use, for industrial environments, heavy manufacturing, or areas subject to constant forklift traffic, we recommend the Labfender Polyurethane System. Mixing and Application Instructions Step 1 Pre Mix This product features a 3 to 1 mix ratio (three parts resin to one part catalyst). This is a water based product, settlement is normal and expected. Blend the bucket of BASE (Part A) for 1 minute before pouring into a larger bucket and combining with activator. Step 2 The Blend For 1 Gallon Kits: Pour Part A and Part B into a larger mixing bucket and blend for 2 minutes using a paddle mixer. For 2 or More Gallons: When mixing multiple kits together (up to 4 gallons in a 5 gallon bucket), you must use a Box Mixer and blend for 2 - 3 minutes to ensure a complete chemical reaction. Step 3 Application Pour the mixed material 1 - 1.5 gallons at a time into an 18 inch paint tray. While wearing spiked shoes and using a 1/4 or 3/8” nap epoxy roller (ensure the roller is de-shedded prior to use), load your roller and cover an area 4 ' x 4' rolling out the material in a "M" pattern left to right, then a "W" pattern right to left, leaving no roller lines behind. For large areas Multiple people should work this pattern loading the floor as one "Finisher" walks side to side back rolling the material over lapping by 2 inches with each pass. Do not wait to back roll as the product can tack over quickly and roller pickup may occur Small Projects: You may utilize a paint tray and dip and roll using a 1/4 or 3/8” nap epoxy roller (ensure the roller is de-shedded prior to use). To avoid roller lines, you may backroll the floor before the product becomes tacky. The "Orange Peel" Mitigation Tip To achieve a professional, smooth finish and eliminate the "orange peel" texture typical of standard urethanes, add 12 ounces of water per kit into the initial mix. This improves the flow and leveling characteristics, resulting in a significantly smoother, more consistent surface reflection. ⚠️ ENVIRONMENTAL WARNING: Do not apply in direct sunlight or on sunbaked surfaces. Additionally, do not apply with air blowing directly on the floor from fans or HVAC systems. Moving air will cause the coating to skin over before it has a chance to properly lay down, leading to permanent surface defects. Coverage Rate Chart Coverage varies based on dilution and application type. Use the following table as a guide: Application Type Strength Approx. Coverage (SFPG) Metallic Floors (Smooth Finish) Diluted (12oz Water) 500 – 600 SFPG Solid Color (Light Duty) Diluted (12oz Water) 500 – 600 SFPG Partial Flake Floors Full Strength 400 – 500 SFPG Commercial Use (Clear) Full Strength 400 – 500 SFPG Pigmented Urethane (Solid) Full Strength Up to 300 SFPG Pigmented Urethane (Smooth) Diluted (10% Water) 375 – 425 SFPG Cure Schedule and Recoating Tack Free: 6 to 8 Hours Recoat Window: 12 to 24 Hours Heavy Foot Traffic: 48 Hours Vehicular Traffic: 72 Hours Sanding Requirements: A second coat may be applied within 24 hours without sanding. After 24 hours, you must sand the surface with 100-120 grit to create a mechanical bond before applying additional coats. Frequently Asked Questions Will I get roller lines if I use this urethane topcoat?Roller lines are almost always a result of improper application technique. To ensure a uniform finish, it is critical to use an 18-inch roller for your main floor area. This provides equal down pressure across the entire surface, preventing the "squeeze lines" commonly caused by 9-inch roller frames. Use a 9-inch roller only for detail work along the edges. Do I need a primer if I am doing a "Grind and Seal" directly on concrete?If you apply urethane directly to raw concrete, expect to apply multiple layers as the porous slab will "drink" the material. To prevent an uneven finish and save on material costs, we highly recommend first applying our One Stop WB Primer. This seals the concrete and provides a consistent foundation for the urethane. How do I stop my urethane from having an orange peel texture?Standard urethanes are thick. By adding 12 ounces of water to your mixed kit, the product thins just enough to level out perfectly, eliminating almost all orange peel characteristics for a much smoother finish. Is this product suitable for a warehouse with forklifts?While this urethane is very scratch resistant, it is designed for foot traffic and light vehicular use. For industrial environments with constant forklift traffic, our Labfender Polyurethane is the recommended system. Why is sanding required after 24 hours?After 24 hours, the surface becomes too smooth for a chemical bond. Sanding creates a mechanical profile that allows the new layer to anchor securely to the previous one. Can this be used for outdoor concrete?No. This is an interior topcoat. For exterior patios or driveways, use a specialized exterior-grade breathable sealer designed to handle moisture movement through the slab. Can I apply this over a previous coating?The surface must be thoroughly cleaned and mechanically sanded to ensure a proper bond. Applying over an old coating without proper mechanical preparation will likely result in delamination. What is the effect of high humidity on application?Humidity above 75% can slow the evaporation of water from the coating, which may cause a cloudy or "milky" finish. It is best to maintain a controlled interior environment during the cure.