APF Polyurethane 100 VOC Satin - Aliphatic Polyurethane Topcoat Product Overview APF Polyurethane 100 is a two-component, high-solids aliphatic polyurethane coating engineered for high-performance flooring and protective coating applications. This topcoat delivers a hard, flexible film with excellent impact resistance, abrasion resistance, and long-term durability in both interior and exterior environments. Formulated with an integral UV additive, APF Polyurethane 100 offers excellent performance under sunlight and strong artificial light. The high-gloss finish is easy to clean and resists staining, chemical attack, and graffiti. A curing accelerator is available for faster turnaround times and is required for the satin finish option. Key Features High-Gloss & Satin Options: Provides superior appearance and protection in both finishes. UV-Stable & Weather Resistant: Performs reliably in outdoor and high-light environments. High Impact & Scratch Resistance: Ideal for heavy-duty commercial floors. Fuel & Chemical Resistant: Withstands exposure to harsh substances. Flexible Yet Hard Surface: Balances durability with application versatility. Optional Curing Accelerator: Speeds up dry times when needed. Recommended Uses Topcoat for color quartz and vinyl flake flooring systems Automotive repair shops and garages Aircraft hangars and service bays Clean rooms and hygienic spaces Interior or exterior wall surfaces requiring graffiti resistance Installation Notes APF Polyurethane 100 should be applied over a properly prepared and cured base system using a roller or squeegee. The product is available in both gloss and satin finishes. When using the satin finish, a curing accelerator must be added. For optimal performance, follow APF's technical data sheet regarding spread rate, cure time, and surface preparation requirements.  

LABFENDER Aliphatic Polyurethane | Heavy Duty Floor Protection Topcoat Product Overview LABFENDER is a high solids, low VOC aliphatic polyurethane topcoat engineered for maximum durability in demanding environments. Designed to be applied over epoxy and polyaspartic systems, it provides exceptional abrasion resistance, superior chemical protection, and long term UV stability. This is the topcoat used when standard systems are not enough and long term performance under heavy traffic is required. LABFENDER significantly reduces wear from foot traffic, forklifts, and rolling equipment while protecting against staining, chemical exposure, and plasticizer transfer. Key Advantages Extreme Abrasion Resistance: Designed for heavy traffic and industrial use Superior Chemical Protection: Up to 60 times more resistant to plasticizer transfer (common cause of staining and softening in coatings) UV Stable: Non yellowing and protects underlying coatings High Solids Formulation: Strong, dense protective layer Low VOC: Suitable for regulated environments Long Working Time: Allows efficient installation over large areas Improved Cleanability: Resists dirt penetration and surface staining Where This Product Is Used Warehouses and manufacturing facilities Forklift and heavy equipment traffic areas Automotive shops and service centers Commercial kitchens and food processing plants Hospitals, labs, and clean environments Flake, quartz, and metallic flooring systems Surface Preparation Requirements LABFENDER is not designed for direct application to concrete. Apply only over epoxy or polyaspartic systems No prep required if within recoat window If outside recoat window, sand to a uniform dull finish Vacuum thoroughly and wipe clean before application Critical Mixing Instructions Mixing errors are one of the most common causes of failure with this product. Follow these instructions carefully. 3 Part Mix (Recommended) Ratio: 4 Parts A to 1 Part B plus 3 lbs Aluminum Oxide (Part C) Pre-mix Part A for 1 minute Add Part B and mix for 3 minutes at low speed (300–450 RPM) Reverse mixer direction for final 90 seconds Scrape sides and bottom of container thoroughly Add Aluminum Oxide slowly and mix an additional 2–3 minutes Recommended dosage: 3 lbs aluminum oxide per 1 gallon kit 2 Part Mix (Smooth Systems) Ratio: 4 Parts A to 1 Part B Follow same mixing procedure without adding aluminum oxide Use this method for smooth floor finishes Do not add solvents. Ensure mixing container is clean. Application Guidelines Apply between 50°F and 86°F with humidity below 80% Turn off ventilation and airflow during application Block wind when applying outdoors Apply using a roller or approved method with consistent coverage to maintain a uniform finish Why Installers Choose LABFENDER When floors are exposed to constant traffic, heavy loads, or chemical exposure, standard topcoats can wear down quickly. LABFENDER provides a higher level of protection that helps maintain the appearance and performance of the entire system over time. This is the solution for long term durability in high demand environments. Frequently Asked Questions Can I apply this directly to concrete?No. This product is designed as a protective topcoat over epoxy or polyaspartic systems. Do I need to add aluminum oxide?It is recommended for flake and quartz systems to improve durability and slip resistance. What happens if I mix it incorrectly?Improper mixing can lead to soft spots, poor curing, or complete coating failure. Follow mixing instructions exactly. Is this suitable for heavy traffic areas?Yes. It is specifically designed for high traffic, industrial, and forklift environments. Does this product yellow?No. It is UV stable and will not yellow over time.

LABPOX 30 100% Solids Epoxy | Professional Flooring System LABPOX 30 is a professional grade, 100% solids epoxy engineered for installers who demand reliability and extended working time. Whether used as a base coat, body coat, or the foundation for metallic epoxy systems, LABPOX 30 delivers the consistency required for high performance industrial, commercial, and residential environments. The Professional Advantage: Unlike limited use epoxies that flash quickly, LABPOX 30 provides a balanced 45 to 60 minute working window, ensuring superior flow, pinhole mitigation, and a glass like finish even on large scale installations. Technical Performance Snapshot Property ASTM Standard / Value Mix Ratio 2 Parts A to 1 Part B Compressive Strength 13,000 psi Tensile Strength 8,500 psi Shore D Hardness 82 Elongation 14 percent VOC Content 9 to 10 g per L (Low VOC) Pot Life (72°F) 50 minutes Where LABPOX 30 Fits in a Flooring System 1. As a High Adhesion Base Coat Provides a consistent, durable foundation for solid color, flake, or quartz broadcast systems. LABPOX 30 is self priming and can be applied directly to properly prepared concrete under the right conditions. 2. As a Metallic Body Coat ("The Money Coat") Specifically optimized for metallic epoxy systems. The extended open time allows for intricate pigment movement and pattern development before the resin sets. 3. As an Intermediate Build Coat Increases overall system thickness and impact resistance in heavy traffic industrial or warehouse environments. Approximate Coverage Rates Application Type Square Feet Per Gallon (SFPG) Metallic Body Coat 50 SFPG Metallic Base Coat 80 to 135 SFPG Vinyl Flake Receiver Coat 133 to 150 SFPG Commercial/Industrial Solid Color 80 to 133 SFPG LABPOX 30 vs. Typical 100% Solids Epoxy Why professional installers choose LABPOX 30 over standard alternatives: Pinhole Mitigation: Advanced technology reduces surface defects by up to 98 percent in pre tinted versions. Extended Control: 60 minutes of working time vs. the standard 20 to 30 minutes of typical epoxies. Chemical Resistance: Superior resistance to amine blush and common site contamination. Cure Schedule (At 72°F) Working Time: 60 Minutes Tack Free: 9 Hours Recoat Window: 9 to 24 Hours Foot Traffic: 24 Hours Full Chemical Cure: 7 Days System Limitations LABPOX 30 requires a dry substrate. Moisture content must be below acceptable limits unless a moisture mitigation system is used. Not intended for exterior applications. Recommended System Setup For a guaranteed bond and long term finish, follow this professional stack: Primer: LAB Surface Epoxy Primer or LABPOX MVB Clear Fast for moisture vapor barriers. Base/Body: Apply LABPOX 30 (Solid Color or Metallic). Topcoat: Seal with LABFAST Xtra Time (Polyaspartic) or LABFENDER Polyurethane for maximum abrasion resistance. Mixing and Application Requirements Application Equipment 1/8 inch notched rubber squeegee 3/8 inch nap woven shed resistant roller cover 3 inch chip brush Mixing Instructions Precision in the mixing process is critical to ensure the chemical bond and structural integrity of the LABPOX 30 system. Combine Components: Pour 2 containers of Part A (Base) into a large mixing bucket, being careful not to pour material onto the sides of the larger bucket. Add Activator: Pour the Part B (Activator) directly into the center of the large bucket. Again, ensure no material gets on the sides of the Base bucket; failing to do so may leave unmixed resin that causes soft spots on your finished floor. Mixing Time: Mix full kits with a Box mixer for 2 minutes. Use a low-speed drill (300 to 450 RPM) to minimize air entrapment. Scrape Sides: During the mixing process, make sure to scrape the sides and bottom of the mixing container thoroughly so no unmixed material remains. Immediate Placement: Once the product is properly mixed, it needs to be immediately poured onto the floor. Leaving mixed material for too long in a mixing pail will create an exothermic reaction (rapid heat buildup), rendering the product unusable. Application Procedure Application Procedure Pour mixed material in a 20 foot long 12 inch wide ribbon Do not drain or scrape remaining material from the bucket onto the floor. Spread to uniform thickness with a notched squeegee and roll North South and back roll East West to achieve uniform coverage. Roller should be a 3/8 inch shed resistant epoxy roller cover. PRO TIP: For metallic floors, use the extended 60 minute window to manipulate your pigments with a 9/16 inch looped roller or notched squeegee to create depth and movement before the product begins its initial set. Frequently Asked Questions Is LABPOX 30 good for metallic epoxy floors?Yes. It is exceptionally well suited for metallic systems due to its 45 to 60 minute working time and excellent flow characteristics, allowing installers to create flawless designs with proper pigment movement. Can this be used as a base coat?Yes. LABPOX 30 works incredibly well as a dependable, high strength base coat for a wide variety of systems, including solid color, flake, and quartz. Is this product beginner friendly?Because of the extended working time, it is more forgiving than fast cure epoxies, but proper surface preparation and installation technique are still required. How long is the actual working time?You will have approximately 60 minutes of working time at 70°F and 45 minutes at 80°F. Humidity and surface temperature can also affect these windows. What is the mix ratio for LABPOX 30?It is a two component system with a precise mix ratio of 2 Parts A to 1 Part B (2A:1B) by volume. Can this be used for flake floors?Absolutely. It performs as a reliable receiver coat for broadcast flake systems, providing enough open time to ensure a consistent flake distribution. Why is the "Extended Working Time" so important?Standard epoxies can flash quickly in the bucket, leading to stress and mistakes. LABPOX 30 gives you a massive window to maintain a wet edge on large floors and execute intricate metallic designs without the product locking up prematurely. Does this require a topcoat?Yes. Like all 100 percent solids epoxies, a UV stable topcoat (like Polyaspartic or Urethane) is highly recommended to prevent ambering and provide long term scratch resistance.

Premera Crystal Densifier – Fast-Acting Concrete Densifier for a Mirror Finish Premera Crystal Densifier is an essential part of the One Day Polish system, designed to densify and polish concrete surfaces efficiently. This advanced product forms a crystal-clear, quartz-mineral barrier both within and on top of the concrete, providing excellent chemical resistance and long-lasting durability. Premera Crystal Densifier is applied directly to 100 transitional profile concrete, allowing you to skip resin applications and proceed straight to burnishing. After one hour, the surface can be burnished with up to a 3000 grit diamond pad, producing a stunning, mirror-like finish. This process significantly reduces labor time while ensuring superior hardness and resistance for high-traffic areas. For optimal protection, follow up with Premera's Crystal Guard which adds a layer of stain and abrasion resistance to your polished concrete, ensuring long-term durability against common food and drink spills. Key Features    Sol-Gel Based SiO2 Densifier: Enhances surface density and strength. Easy Application: Spray-on formula for 100 transitional finish. Fast Burnishing: Begin burnishing 1 hour after application. No Resins Needed: Skip straight to burnishing with diamond pads. Mirror Finish: Achieve high gloss with up to a 3000 grit pad. Durable Protection: Forms a dense, polishable surface layer. For enhanced protection, complete your concrete polishing system with Premera's Crystal Guard

Premera Crystal Guard Ultimate Stain and Abrasion Resistance for Polished Concrete Premera Crystal Guard is an essential component of the One Day Polish system, designed to protect and enhance polished concrete surfaces. This two-step process begins with Crystal Densifier, followed by Crystal Guard, a single-component polycarbonate polymer that offers unmatched stain and abrasion resistance. With its advanced formula, Premera Crystal Guard protects against common food and drink stains like coffee, red wine, vinegar, and soda. It can also be easily burnished to maintain a brilliant shine. Whether you’re polishing concrete in residential, commercial, or industrial spaces, Crystal Guard delivers several hours to permanent protection, ensuring your floors stay looking their best with minimal maintenance. Key Features: VOC-Compliant: Low odor, water-based formula meets environmental standards. Single-Component Design: Simplifies application using a microfiber pad. Exceptional Stain Resistance: Safeguards polished concrete against food and drink stains. Durable Abrasion Resistance: Keeps floors looking new, even in high-traffic areas. UV-Stable, Non-Yellowing: Maintains clarity and appearance over time. Easy Maintenance: Easily burnished with a white pad for quick shine restoration. Cost-Efficient: Reduces maintenance costs with its easy-clean effect. Application Process: Apply Crystal Guard with a microfiber pad. Burnish using a 3000-grit diamond pad. Finish with a white buffing pad for high gloss and durability.

Self Leveling 100% Solids Industrial Grade Epoxy One Stop Epoxy Self Leveling 100% Solids Industrial Grade Epoxy is a professional grade, high build floor coating engineered for extreme durability in residential, commercial, and industrial environments. This self leveling resin creates a seamless, high gloss surface with superior adhesion and the chemical resistance required for long term performance. Sold as a 3 gallon short fill kit, this system arrives clear or pre pigmented in white, light gray, medium gray, black, or tan to save you time and eliminate mixing errors on the jobsite. What Is a 100% Solids Industrial Epoxy? Unlike water based or solvent based store coatings, a 100% solids epoxy contains no fillers that evaporate during the curing process. This means the thickness you apply wet is exactly the thickness that remains when dry. This "high build" characteristic is what allows the material to self level, filling minor imperfections in the concrete to create a heavy duty finish. Why Professionals Choose Pre Pigmented Short Fill Kits Eliminate Mixing Errors: No separate pigment packs to measure; the color is already balanced in the resin. In-Bucket Mixing: The "short fill" design allows you to add Part B directly into the Part A bucket, saving you the cost of extra mixing pails. Consistency: Ensures perfect color uniformity across large multi kit pours. Versatility: Use as a standalone solid color floor, a receiver coat for flakes, or a structural base for metallic designs. Mixing and Application Requirements Mix Ratio: 2 Parts A to 1 Part B. Mix Time: 3 Full Minutes at 300 to 450 RPM. Working Time: 45 Minutes on the floor (8 minutes if left in the bucket). Traffic Ready: 24 Hours for foot traffic; 7 days for full chemical cure. Frequently Asked Questions Is this a true 100 percent solids epoxy?Yes. This is a true 100 percent solids industrial resin containing no water or solvents. The thickness you apply wet is the thickness that remains after cure. Is this a good epoxy for garage floors?Yes. It is the gold standard for garage floor coatings because it provides the high build and chemical resistance needed to withstand hot tires and automotive fluids. Does this come pre pigmented?Yes. Our short fill kits arrive pre pigmented in White, Black, Light Gray, Med Gray, and Tan, ensuring color consistency and ease of use. Do I need a separate mixing bucket?No. The short fill design allows you to pour Part B directly into the Part A bucket for convenient mixing. How long should I mix the epoxy?Mix for a minimum of 3 minutes using a low speed drill and a cage style mixer to ensure a complete chemical crosslink. What is the working time once mixed?Once poured onto the floor, you have approximately 45 minutes at 75 degrees. If left in the bucket, the material can harden in less than 10 minutes (exotherm). Can this be used for a full flake floor?Yes. It is an excellent pigmented receiver coat for vinyl flakes. For a pro finish, topcoat with PolyGloss 85 Polyaspartic after scraping the flakes. Does surface prep matter with self leveling epoxy?Absolutely. Proper mechanical grinding to a CSP 2 or 3 profile is required for a permanent bond. Self leveling refers to the finish, not prep. Can I use this as a base for metallic floors?Yes. It provides a stable, uniform pigmented foundation for Metallic Dream Epoxy body coats. How many square feet does a kit cover?A 3 gallon kit typically covers 400 to 450 square feet as a receiver coat for flakes or 300 to 400 square feet for a high build solid color finish.