LABFENDER™ Aliphatic Polyurethane Floor Coating Product Overview LABFENDER™ (NEW) is a two- or three-component, high-solids, low-VOC aliphatic polyurethane topcoat designed to protect LABPOX® epoxies, LABFAST® Polyaspartics, and LABSHIELD® ECO coatings. It provides exceptional abrasion resistance, superior chemical protection against plasticizer transfer, and UV resistance to delay yellowing. Key Features High-solids aliphatic polyurethane formula Low-VOC for LEED eligibility Exceptional abrasion resistance for heavy traffic Superior chemical resistance—up to 60× more against plasticizer transfer Enhanced UV protection to delay epoxy yellowing Long working time for large-area installations 240 Grit Aluminum Oxide Recommended Uses Protective topcoat over epoxy and Polyaspartic systems Warehouses, manufacturing and industrial facilities Automotive shops, garages, and service centers Commercial kitchens and food processing areas Laboratories, hospitals, and cleanroom environments High-traffic retail and showroom floors Installation Notes Mix components A and B (and C if required) per manufacturer instructions Stir gently to minimize air entrainment Apply with a roller or airless sprayer at recommended coverage Maintain ambient temperature between 50–90 °F Allow light foot traffic after 12–24 hours and full cure in 7 days

APF Oil Stop Primer – Epoxy Primer for Oil-Contaminated Concrete Floors APF Oil Stop Primer is a professional-grade 100% solids epoxy primer formulated to bond to oil-soaked or hydrocarbon-contaminated concrete. Whether you’re dealing with motor oil, hydraulic leaks, solvents, or transmission fluid, this low-viscosity formula penetrates deep into the slab and delivers a reliable bond where other primers fail. For garages, machine shops, or industrial floors with embedded oils, APF Oil Stop Primer helps prevent delamination and promotes long-term adhesion of your epoxy system. Key Benefits Bonds to Oil-Contaminated Concrete – Engineered for surfaces affected by oils, fuels, and solvents. Excellent Surface Tolerance – Works even when surface prep isn’t perfect. Strong Adhesion – Reliable base layer for flake, solid color, or industrial epoxy systems. Efficient Coverage – Covers approximately 125 sq ft per kit using a 3A:2B mix ratio. Recommended Applications Auto repair shops and service bays Garage floors and residential workshops Machine shops with oil or fluid residue Warehouses with forklift or vehicle leaks Note: Not intended for food-grade environments, chemical processing plants, or areas routinely cleaned with hot water or aggressive detergents. Contact APF Technical Support for those applications. Product Specs Color: Clear (not tintable) Mix Ratio: 3A:2B by volume Kit Size: 1.25 gallons Coverage: ~125 sq ft Type: 100% solids epoxy primer VOC: Low Start with the Right Primer APF Oil Stop Primer gives you confidence when applying epoxy over oil-stained or solvent-penetrated concrete. Avoid costly failures by using the right product on the first coat. A clean bond means no peeling, bubbling, or lifting—just a professional finish that lasts.

DIYers & Professional Painters Trust Our Epoxy Garage Floor Coating Pro-Grade Results Without Pro-Level Equipment If you're searching for a dependable, long-lasting garage floor epoxy kit, you're in the right place. Whether you’re a homeowner doing it yourself or a painter taking on a residential job, this system was built to deliver real results—without the guesswork or expensive equipment. Many of our clients have used—or watched friends and family use—popular kits like Rustoleum RockSolid® or EpoxyShield®, only to be disappointed by peeling, hot tire pickup, or early wear. That’s why more people are turning to One Stop Epoxy—it’s easier to install, offers superior adhesion, and gives you professional-level durability even if it’s your first time working with epoxy. Why DIYers Prefer This Kit No pouches or special tools – Mix with a drill and paddle, apply with a roller More working time – Up to 2 hours pot life gives you breathing room Epoxy coating that holds up – Built to resist wear, tear, and hot tires Hot tire resistant – When installed after acid etching or grinding as directed, delamination is highly unlikely Why Professional Painters Trust It Ideal for garage floor jobs – No need for industrial prep or equipment Easy to schedule and apply – Low odor and fast cure time make residential projects simple Confidence in the result – Reliable finish without taking on the complexity of pro-level systems Flexible Application Options Apply two lighter coats for best results and long-term durability Or go with one heavier coat when working under time constraints Either method delivers a strong, uniform finish that lasts Product Highlights Durable like 100% solids epoxy, without the prep work, specialty tools, or pressure to rush the install Two-Part Kit: Pre-pigmented Part A (Base) + Activator Part B Coverage: Up to 200 sq. ft. per kit, depending on concrete porosity Pot Life: ~2 hours @ 75°F; ~1 hour @ 90°F Cure Time: Walkable in 24 hours, vehicle-ready in 72 hours What’s Included ¾ Gallon of Epoxy Base (Part A) 1 Quart of Activator (Part B) Clear instructions for prep, mixing, and installation Use as a standalone epoxy system or add flakes for a decorative garage floor and seal with our user friendly urethane or if you really want to go all out use our PolyGloss 85 Slow Cure to add a bullet proof finish. Ideal For Homeowners upgrading from DIY big-box garage floor kits Painters who want quality installs without industrial systems Property investors, flippers, and remodelers needing a reliable solution Anyone ready to stop wasting money on coatings that peel or fail Real Performance. Long-Term Confidence. With One Stop Epoxy, you get lasting durability and professional results—without needing industrial tools or training. When installed according to instructions, this garage floor epoxy provides a high-quality, long-lasting finish that holds up for years against everyday use, including hot tire traffic and chemical spills. Order now at OneStopEpoxy.com

APF VaporSolve® LP – Low Perm Moisture Mitigation Epoxy Product Overview APF VaporSolve® LP is a 100% solids, low-permeance epoxy specifically engineered to isolate moisture-sensitive flooring systems from high-moisture concrete. Designed for use where concrete exhibits up to 99% RH (per ASTM F2170), this single-coat system is part of the APF VaporSolve Ultra System and exceeds ASTM F3010 standards for moisture mitigation. This coating should only be applied over concrete that has never been treated with reactive silicate curing compounds or densifiers. If sodium or potassium silicates are present—or suspected—the APF VaporSolve Primer is required. Surface shot-blasting alone is not effective at removing metasilicate residues. Key Features Controls High Moisture Levels: Suitable for substrates with up to 99% relative humidity (RH). Single-Coat Application: No primer needed when silicates are not present. Superior Adhesion: Formulated for excellent substrate wetting and penetration. Low Perm Rating: Protects against moisture vapor transmission. Damp Concrete Application: Advanced curing agent allows installation over damp surfaces. Application Temperature Range: 65°F to 85°F (18°C to 30°C). Recommended Uses Commercial concrete floors with elevated RH levels Pre-installation under sensitive floor coverings Moisture remediation in slab-on-grade construction Installation Notes For best results, install APF VaporSolve® LP over properly prepared concrete using a notched squeegee and back-rolling method. If silicate-based curing agents or densifiers have been applied to the concrete, use VaporSolve Primer before applying this product. Do not apply below the minimum temperature range. Always follow manufacturer’s technical data sheet for coverage and cure times.

APF Polyurethane 100 VOC Satin - Aliphatic Polyurethane Topcoat Product Overview APF Polyurethane 100 is a two-component, high-solids aliphatic polyurethane coating engineered for high-performance flooring and protective coating applications. This topcoat delivers a hard, flexible film with excellent impact resistance, abrasion resistance, and long-term durability in both interior and exterior environments. Formulated with an integral UV additive, APF Polyurethane 100 offers excellent performance under sunlight and strong artificial light. The high-gloss finish is easy to clean and resists staining, chemical attack, and graffiti. A curing accelerator is available for faster turnaround times and is required for the satin finish option. Key Features High-Gloss & Satin Options: Provides superior appearance and protection in both finishes. UV-Stable & Weather Resistant: Performs reliably in outdoor and high-light environments. High Impact & Scratch Resistance: Ideal for heavy-duty commercial floors. Fuel & Chemical Resistant: Withstands exposure to harsh substances. Flexible Yet Hard Surface: Balances durability with application versatility. Optional Curing Accelerator: Speeds up dry times when needed. Recommended Uses Topcoat for color quartz and vinyl flake flooring systems Automotive repair shops and garages Aircraft hangars and service bays Clean rooms and hygienic spaces Interior or exterior wall surfaces requiring graffiti resistance Installation Notes APF Polyurethane 100 should be applied over a properly prepared and cured base system using a roller or squeegee. The product is available in both gloss and satin finishes. When using the satin finish, a curing accelerator must be added. For optimal performance, follow APF's technical data sheet regarding spread rate, cure time, and surface preparation requirements.  

APF Polyurethane 250 Gloss– Acrylic Urethane Primer & Sealer for Concrete Product Overview APF Polyurethane 250 Gloss is a two-component, low-viscosity acrylic urethane designed for use as a primer or sealer over concrete, architectural surfaces, and decorative finishes. This product offers superior penetration and adhesion to minimally profiled concrete thanks to its unique blend of solvents and adhesion promoters. UV stable and fast-curing, it can be used in both interior and exterior applications and re-coated with either water-based or solvent-based polyurethanes.  As a finish coat, APF Polyurethane 250 delivers a hard, Gloss surface with excellent stain resistance, Satin retention, and easy cleanability. It outperforms traditional solvent-based acrylic sealers and is available in a satin finish.  Key Features Excellent Penetration & Adhesion: Bonds well to low-profile concrete and difficult substrates. UV Stable & Fast Curing: Suitable for outdoor use with rapid dry and recoat times. Color Enhancement: Improves appearance over acid-stained and integrally colored concrete. Stain & Chemical Resistant: Resists tire marking, graffiti, fuels, and many common chemicals. Re-Coatable: Compatible with both water-based and solvent-based polyurethane topcoats. Low VOC Option Available: Meets air quality regulations for restricted regions. Recommended Uses Primer for Color Quartz and Vinyl Flake Systems Topcoat for Armor-Rez Concrete Grind & Seal applications Concrete and acid-stained surfaces Retail stores, restaurants, and commercial floors Warehouses and aircraft hangars Automotive service areas and showrooms Installation Notes APF Polyurethane 250 Gloss should be applied to clean, dry, properly prepared surfaces using a roller or airless sprayer. When sealing over acid-stained or integrally colored concrete, ensure adequate ventilation and monitor surface temperatures. This product may also be used as a tie coat over hard-to-bond coatings such as polyester urethane. For best results, follow APF’s application guidelines for spread rates and cure times.  

APF VaporSolve® Primer – Water-Based Epoxy for High Moisture Concrete Product Overview APF VaporSolve® Primer is a specially formulated, water-based epoxy primer designed to deliver superior adhesion to concrete with high moisture vapor emission. When paired with APF VaporSolve LP, it completes the APF VaporSolve Ultra System, reducing moisture vapor emissions to acceptable levels while maintaining bond integrity under continuous moisture and alkaline conditions. This primer is formulated specifically for concrete treated with silicate-based curing compounds or densifiers, where shot-blasting alone cannot fully remove metasilicate residues. Its low viscosity promotes excellent substrate wetting and penetration for reliable adhesion, even over damp concrete. Key Features Moisture Mitigation: Designed for high moisture content concrete substrates. Bisphenol F Resin Technology: Provides outstanding resistance to water and alkalinity. Compatible With Silicate-Treated Concrete: Formulated for surfaces treated with sodium or potassium silicates. Damp Surface Application: Adheres to damp concrete surfaces. Wide Application Temperature Range: Can be applied between 40°F and 100°F (4°C to 38°C). Recommended Uses Concrete floors with high moisture vapor emissions Substrates treated with silicate-based curing agents Pre-installation moisture remediation prior to finish coats Installation Notes Apply APF VaporSolve® Primer to properly prepared concrete using a roller or squeegee, following the manufacturer’s coverage and cure rate guidelines. Ensure the surface temperature is within the recommended application range. Follow with VaporSolve LP as the finish coat to complete the moisture mitigation system.  

Labshield Eco Prolonged Working Time (+) The LABSHIELD® ECO is a virtually odor-free, 100% solids, two-component (2A:1B), and non-yellowing polyaspartic for concrete floor coating, commonly used with vinyl flakes. The colored LABSHIELD® ECO serves as the base coat, while the clear version is used as a protective topcoat, both sharing a common hardener. LABSHIELD® ECO offers two variations (Ultra-Fast Set (-) and Prolonged Working Time (+)). LABSHIELD® ECO provides an optimal work time/cure time ratio. The utilization of the LABSHIELD® ECO allows the installation of a full floor system in one single day, with rapid return to service. The product displays excellent curing capability even at very low temperature levels. It offers superior mechanical and chemical properties, is low maintenance, and exhibits a superior aesthetic finish with excellent UV stability, making it optimal for both interior and exterior applications. We recommend using LABTEC vinyl chips in combination with LABFAST®/LABSHIELD® ECO products. Two- or three-coat systems can be considered.

Poly Gloss 85 Slow Go Polyaspartic Floor Coating Product Overview Poly Gloss 85 Slow Go is a two-component, 1:1 aliphatic Polyaspartic designed for projects that need extra working and cure time. You get the same industrial-strength, high gloss finish as our standard Poly Gloss 85, plus extended open time, high build in a single coat, and superior resistance to stains, chemicals, and UV. Key Features 60 minutes working time up to 85 degrees Apply up to 10 mils in one pass without whitening Non-porous, easy-clean sealed surface Abrasion and scratch resistant 85% solids for high-build performance UV stable and non-yellowing Plasticizer free to prevent tire staining Wide temperature range and fast return to service Recommended Uses High traffic commercial and industrial floors Residential garage flake floor systems Protective finish coat for solid color and Metallic epoxy floors  Cold storage and cleanroom areas Restaurants, bars, and commercial kitchens Sports arenas and showroom floors Hair salons, aircraft hangers, and schools Coverage & Application 1 gal kit covers 133–150 sq ft 2 gal kit covers 266–300 sq ft 3 gal kit covers 399–450 sq ft Apply with flat squeegees on flakes and 1/8 inch notched squeegee on smooth surfaces, roll and back roll with shed resistant rollers, use chip brushes for corners

Performance Benefits High bond strength to concrete substrates for long lasting adhesion. Excellent durability and chemical resistance for demanding environments. Recommended Applications Crack and surface defect repair prior to epoxy flooring. Filling voids, pinholes, and minor surface imperfections. Surface preparation before installing resinous floor systems. Typical Uses Industrial and manufacturing facilities. Warehouses and logistics centers. Commercial and retail floors. Garages and parking structures. Food and beverage processing areas. Healthcare, educational, and pharmaceutical facilities. OneStopEpoxy.com where nationwide shipping on crack and joint fillers is always free.

One Stop Epoxy Urethane - WB One Stop Epoxy Urethane - WB is a two component system with excellent scratch and chemical resistance in an easy to mix 3:1 kit consisting of 3 parts urethane resin to one-part catalyst by volume. One Stop Epoxy Urethane is water based and available in Glass, Satin, and Matt and 1, 4, and 15 gallon kits. Use One Stop Epoxy Urethane - WB As a Seal Coat For Retail and Commercial Flooring Garage and Showroom Floors High-Traffic Interior Applications Restaurants and Bars Sports Arenas Automotive Service Areas Hair and Beauty Salon Commercial Kitchen Garages – Preferred Seal Coat For Partial Flake Floors Aircraft Hangers Schools and Universities Can also be used directly on a concrete floor for a very durable and cost effective grind and seal. Approved Basecoats for Urethane - WB Water-based or 100% solids epoxy: Metallic Dream Epoxy Self Leveling 100% Solids High Strength Epoxy Dye Stained Floors Concrete Countertops Surface Prep & Priming When applying over epoxy, grind concrete floors to CSP-3, vacuum dust, wipe with denatured alcohol and apply epoxy. No need to sand when apply as epoxy seal coat within 24 hours of application of waterbase or 100% solids epoxy. A chemical bond will form. Sand first when applying as epoxy seal coat after 25 hours of application to 100% solids epoxy to form a mechanical bond. When applying directly to a concrete floor for a grind and seal, Grind concrete floors to a CSP that provides the texture you’re looking for, vacuum dust, wipe with Denatured alcohol apply Tru-Alpha Water-Based Urethane clear or pigmented directly to the concrete. ( a second or third coat may be applied to attain the desired look or level of durability.) Mixing One Stop Epoxy Urethane - WB Partial kits: If mixing less than a full kit, mix three Parts A to one Part B by volume at low speed mix for two minute. Full kits: Open quart of Part B pour contents into the pail containing gallon of premeasured Part A. Stir with a jiffy mixer for 2 minutes to ensure material is mixed well. Avoid whipping air into the coating. Improper mixing may result in product outgassing. Recommended: Add 8-10oz of water for increased ease of usability and smoothness Application Mixed material can be dipped and rolled evenly with 3/16” nap roller to maintain the desired thickness. Back rolling is recommended to obtain uniform finish. Add Aluminum Oxide for slip resistance if desired. Coverage per Kit Topcoat for Metallic Floors 500-600 sq ft Topcoat for Solid Color Floors 500-600 sq ft Topcoat for Partial Flake Floors 400-500 sq ft Pigmented Urethane 400 sq ft  Best if applied at temperatures between 55-90 degrees Fahrenheit. Dry time & Recoat Tack free/foot traffic: 6-8 hrs. Recoat 12-24 hrs. Heavy foot traffic 48 hrs. Vehicular Traffic 3 days. Lightly sand the surface and wipe down with denatured alcohol or acetone before applying additional coats or finish coats.