Garage Floor Epoxy That Actually Works | Built for DIYers, Painters, and Handymen

Stop Wasting Time on Kits That Fail

If you're here, there's a good chance you've seen what happens with big box epoxy kits. Peeling. Hot tire pickup. Thin coatings that wear out in months. Most store bought kits are closer to reinforced enamel paint than a true industrial coating.

One Stop Epoxy gives you a true industrial grade, two component epoxy coating that actually stays put.

This system was engineered to bridge the gap between cheap DIY kits and complex contractor systems. It delivers a professional grade bond and a clean, high gloss finish without requiring specialized equipment or a large crew.

Why This Epoxy Kit Outperforms Big Box Store Options

• Real Epoxy Chemistry: Not a watered down latex epoxy hybrid. This is a true cross linking resin system.
• Superior Bond Strength: Penetrates the concrete pores to prevent delamination and hot tire pickup.
• Industrial Build: Significantly more material remains on the floor compared to thin, hardware store alternatives.
• No Pouch Guesswork: Comes in real cans. Mix with a drill and you have a professional grade material ready to roll.

The difference comes down to how much actual epoxy is in the coating.

Many store bought kits are diluted with water and fillers, leaving behind a thin coating that wears out quickly. This system contains approximately 58% epoxy solids, which means significantly more actual resin is left behind to create a thicker, stronger bond to the concrete and a finish that holds up over time.

Designed for DIYers, Painters, and Handymen

For Homeowners and Handymen:

• Extended Working Time: Provides up to 2 hours of pot life so you can work at a comfortable pace.
• Simple Application: Applies easily with standard rollers and brushes.
• DIY Friendly: Includes clear, no nonsense instructions for prep and installation.

For Professional Painters:

• Expand Your Services: The perfect entry point for adding garage floors to your residential business.
• Predictable Results: High reliability finish that eliminates call backs caused by kit failures.
• Fast Turnaround: Easily fits into a standard 2 or 3 day project timeline.

Installation Process

Step 1: Surface Preparation

• Bare concrete should be at least 30 days old and free of grease, dirt, and oil.
• Test for moisture: Tape a 2 foot by 2 foot plastic sheet to the floor for 24 hours. If moisture forms underneath, address the moisture issue before coating.
• Test for sealers: Pour water on the slab. If it beads up instead of soaking in, the surface needs additional prep.
• For previously painted floors: Remove all loose or peeling paint by sanding or scraping. Dull glossy surfaces with sandpaper. Do not acid etch painted surfaces.

Step 2: Mixing (Critical Step)

• Open both cans and mix the contents of each separately before combining.
• Pour Part B into Part A. Mix with a low speed drill and mixing paddle for 4 minutes.
• Scrape the sides of the container while mixing. Do not whip air into the product.
• Induction Time: Allow the mixed epoxy to stand for 30 minutes before application. Skipping this step can affect product performance.

Step 3: Application

• Best applied between 55 and 90 degrees. Use a brush for edges and a roller for the main floor.
• Apply in manageable sections to maintain a wet edge.
• If using flakes, broadcast them into the wet epoxy while the coating is still fresh.
• On bare concrete, two coats are recommended for maximum durability and appearance.

Technical Specifications

• Coverage: Up to 200 square feet per kit (supersedes label coverage rates).
• Pot Life: Approximately 2 hours at 75 degrees.
• Cure Schedule: Touch dry in 6 hours; Foot traffic and recoat in 24 hours; Vehicular traffic in 72 hours.
• Kit Contents: 3/4 Gallon Epoxy Base (Part A) and 1 Quart Activator (Part B).

Frequently Asked Questions

What does 58% epoxy solids actually mean?
Solids content refers to how much material remains on the floor after the coating cures. While big box kits are mostly water and fillers, our 58% solids system leaves behind a much thicker, more durable resin film.

Why do cheaper kits peel or fail?
Low solids coatings sit on top of the concrete rather than bonding into it. A higher solids epoxy penetrates and anchors into the concrete, creating a bond that resists hot tire pickup and pressure.

Do I really need to wait 30 minutes after mixing?
Yes. This is called induction time. It allows the chemical reaction to stabilize before you apply it to the floor. Skipping this step can lead to curing issues.

Is this as strong as 100% solids epoxy?
100% solids is the commercial standard. This system is a professional grade balance between extreme durability and ease of installation for DIYers, handymen, and painters.