APF Oil Stop Primer | Epoxy Primer for Oil Contaminated Concrete Product Overview APF Oil Stop Primer is a professional grade 100% solids epoxy primer engineered specifically to bond to oil soaked and hydrocarbon contaminated concrete. When standard primers fail due to embedded oils, this low viscosity formula penetrates deep into the slab to create a reliable and permanent bond. For garages, auto shops, and industrial floors exposed to motor oil, hydraulic fluid, or solvents, this product prevents delamination and provides your coating system a stable starting point. It is the definitive solution when the concrete is already compromised and you still need the floor to perform. Avoid Costly Concrete Replacement: Standard primers cannot bond to contaminated concrete, which leads to peeling and system failure. APF Oil Stop Primer is designed specifically for these conditions, allowing you to successfully coat difficult slabs so you don't have to rip out the floor and replace it. Key Benefits Bonds to Contaminated Surfaces: Specifically designed for slabs affected by oils, fuels, and hydrocarbons. Deep Anchor Penetration: Low viscosity formula helps the resin anchor into compromised concrete pores. Prevents Delamination: Creates a reliable base for epoxy, polyaspartic, and flake systems. Problem Solving Performance: The go to primer when traditional resins will not hold. 100% Solids and Low VOC: Strong build with minimal odor, making it suitable for interior applications. Recommended Applications Auto repair shops and service bays. Residential garage floors and home workshops. Machine shops with frequent oil or fluid spills. Industrial warehouses with heavy forklift traffic. Technical Specifications Property Details Mix Ratio 3 Parts A to 2 Parts B Kit Size 1.25 Gallons Coverage Approximately 125 sq ft per kit Color Clear (Not Tintable) Surface Preparation Concrete must be cured for at least 30 days and structurally sound. Surface must be free of loose coatings, wax, and heavy surface debris. Mechanically prepare the surface to a CSP 2 or CSP 3 profile. Vacuum thoroughly to remove all dust and debris before application. Pro Tip: Apply APF Oil Stop Primer immediately after grinding and surface preparation. On heavily oil-contaminated slabs, embedded oils can migrate back to the surface within hours. Delaying application increases the risk of adhesion failure, so it is best to prep and coat in the same window. Mixing and Application Mixing: Combine Part A and Part B at a 3 to 2 ratio. Mix with a low speed drill for 2 to 3 minutes. Scrape sides and bottom thoroughly. Apply immediately after mixing. Application: Pour in ribbons and spread with a squeegee. Back roll with a solvent resistant 3/8 inch nap roller. Technique: Back roll twice in a north south and east west pattern to ensure the resin fully wets the substrate. Recoat: Apply subsequent coats within 24 hours. If exceeded, sand with 80 to 100 grit until a uniform dull finish is achieved. Frequently Asked Questions Can I use this on a floor that currently has standing oil?No. While it bonds to contaminated concrete, you must first clean and degrease the surface to remove standing oil and surface muck before mechanical preparation. What happens if I use a regular primer on oil soaked concrete?Standard epoxies will likely bead up or fail to bond, leading to fish eyes in the coating and eventual peeling once vehicle tires or heat are introduced. Is this primer clear?Yes. It is a clear 100% solids epoxy. It is not designed to be tinted. Can I apply a flake system over this?Yes. This creates an ideal bond for epoxy base coats, flake systems, and polyaspartic topcoats on compromised slabs.

APF Polyurethane 100 VOC Satin - Aliphatic Polyurethane Topcoat Product Overview APF Polyurethane 100 is a two-component, high-solids aliphatic polyurethane coating engineered for high-performance flooring and protective coating applications. This topcoat delivers a hard, flexible film with excellent impact resistance, abrasion resistance, and long-term durability in both interior and exterior environments. Formulated with an integral UV additive, APF Polyurethane 100 offers excellent performance under sunlight and strong artificial light. The high-gloss finish is easy to clean and resists staining, chemical attack, and graffiti. A curing accelerator is available for faster turnaround times and is required for the satin finish option. Key Features High-Gloss & Satin Options: Provides superior appearance and protection in both finishes. UV-Stable & Weather Resistant: Performs reliably in outdoor and high-light environments. High Impact & Scratch Resistance: Ideal for heavy-duty commercial floors. Fuel & Chemical Resistant: Withstands exposure to harsh substances. Flexible Yet Hard Surface: Balances durability with application versatility. Optional Curing Accelerator: Speeds up dry times when needed. Recommended Uses Topcoat for color quartz and vinyl flake flooring systems Automotive repair shops and garages Aircraft hangars and service bays Clean rooms and hygienic spaces Interior or exterior wall surfaces requiring graffiti resistance Installation Notes APF Polyurethane 100 should be applied over a properly prepared and cured base system using a roller or squeegee. The product is available in both gloss and satin finishes. When using the satin finish, a curing accelerator must be added. For optimal performance, follow APF's technical data sheet regarding spread rate, cure time, and surface preparation requirements.  

APF Polyurethane 250 Gloss– Acrylic Urethane Primer & Sealer for Concrete Product Overview APF Polyurethane 250 Gloss is a two-component, low-viscosity acrylic urethane designed for use as a primer or sealer over concrete, architectural surfaces, and decorative finishes. This product offers superior penetration and adhesion to minimally profiled concrete thanks to its unique blend of solvents and adhesion promoters. UV stable and fast-curing, it can be used in both interior and exterior applications and re-coated with either water-based or solvent-based polyurethanes.  As a finish coat, APF Polyurethane 250 delivers a hard, Gloss surface with excellent stain resistance, Satin retention, and easy cleanability. It outperforms traditional solvent-based acrylic sealers and is available in a satin finish.  Key Features Excellent Penetration & Adhesion: Bonds well to low-profile concrete and difficult substrates. UV Stable & Fast Curing: Suitable for outdoor use with rapid dry and recoat times. Color Enhancement: Improves appearance over acid-stained and integrally colored concrete. Stain & Chemical Resistant: Resists tire marking, graffiti, fuels, and many common chemicals. Re-Coatable: Compatible with both water-based and solvent-based polyurethane topcoats. Low VOC Option Available: Meets air quality regulations for restricted regions. Recommended Uses Primer for Color Quartz and Vinyl Flake Systems Topcoat for Armor-Rez Concrete Grind & Seal applications Concrete and acid-stained surfaces Retail stores, restaurants, and commercial floors Warehouses and aircraft hangars Automotive service areas and showrooms Installation Notes APF Polyurethane 250 Gloss should be applied to clean, dry, properly prepared surfaces using a roller or airless sprayer. When sealing over acid-stained or integrally colored concrete, ensure adequate ventilation and monitor surface temperatures. This product may also be used as a tie coat over hard-to-bond coatings such as polyester urethane. For best results, follow APF’s application guidelines for spread rates and cure times.  

APF VaporSolve LP | 99% RH Moisture Mitigation Epoxy APF VaporSolve LP (Low Perm) is a specialized, 100% solids epoxy coating engineered to isolate moisture-sensitive flooring systems from concrete with high moisture levels. It acts as a high-performance moisture mitigation layer, designed to prevent the devastating flooring failures caused by excessive moisture vapor transmission through the slab. VaporSolve LP is suitable for concrete substrates showing up to 99% Relative Humidity (RH) when measured in accordance with ASTM F2170. It is part of the proven APF VaporSolve system, formulated for low viscosity and superior substrate wetting to promote deep penetration and a permanent bond, even to damp concrete. Technical Performance Snapshot Physical Property Value Maximum Moisture Rating 99% RH (ASTM F2170) Permeability (ASTM E-96) 0.01 Perms Adhesion to Concrete (ASTM D-4541) >500 psi (Concrete Failure) Pot Life / Bucket Time (ASTM D2471) 10–15 Minutes at 77°F VOC Content <50 g/L Critical Bucket Time Warning: VaporSolve LP has an extremely short pot life of 10–15 minutes. You must pour the material out of the pail immediately after mixing. If left in the bucket, the material will rapidly generate heat and kick, significantly reducing your application window. Once spread on the cooler concrete surface, your actual working time will extend, but the material must get out of the pail immediately. The Silicate Conflict If the concrete surface is known or suspected to have been treated with silicates, densifiers, or reactive silicate curing compounds, the use of APF VaporSolve Primer is required before applying VaporSolve LP. Shot-blasting or diamond grinding alone will not reliably remove metasilicate residues from within the concrete pores. In these cases, the primer is a mandatory step to bridge the gap and ensure the system maintains a permanent bond. Where This Product Fits in a System APF VaporSolve LP is used below moisture-sensitive flooring systems (Epoxy, Urethane, Polyaspartic, or Cementitious Overlays) when elevated concrete moisture is present. It is a functional moisture control membrane designed to isolate the finished floor from moisture vapor coming through the slab. Packaging and Coverage Packaging: Supplied in complete A+B units in 1.5 gallon and 3.0 gallon kits. Use only as a complete mixed unit; do not break down into partial mixes. Coverage Rates: To achieve the 0.01 perm rating, the material must be applied at 100 sq. ft. per gallon (16 mils Wet Film Thickness). Proper coverage is critical because moisture mitigation is a thickness dependent application. If spread too thin, the system may fail to isolate moisture vapor effectively. Surface Preparation Concrete must be clean, structurally sound, and mechanically prepared to a minimum ICRI CSP 2 to 3 surface profile. The concrete must be free of wax, grease, loose coatings, curing compounds, and dust. Note: Acid etching is not a professional installation procedure and should not be used in place of mechanical grinding or shot blasting. It does not create a consistent surface profile and may void manufacturer warranties. Mixing Instructions Thoroughly pre-mix Part A before adding Part B. Combine both components and mix for 2 to 3 minutes using a slow-speed drill and paddle mixer. Scrape the sides and bottom of the mixing container during mixing. Do not mix by hand. Do not mix at high speeds, as whipping air into the material can create bubbles, pinholes, and surface defects. Application Instructions Apply VaporSolve LP immediately after mixing. Spread the product with a squeegee and back-roll with a quality solvent-resistant 3/8-inch nap roller cover. The material must be rolled twice to achieve proper substrate wetting and to ensure a pinhole-free seal. Use a North-South and East-West rolling pattern to distribute the product evenly across the prepared concrete. Recoat within the 12–24 hour window. If the 24-hour window is exceeded, you must abrade the surface with 80–100 grit until it is uniformly gloss-free and dust-free before proceeding. Common Frequently Asked Questions Can I use this on "Green" concrete? Concrete typically needs to cure for 28 days before coating. While VaporSolve LP can handle high humidity, it is still recommended to wait for the concrete to stabilize. If you are on a fast-track construction schedule, please contact us to discuss the specific age of your slab before proceeding. Why is the Perm rating so important? A perm rating measures the rate of water vapor transmission. VaporSolve LP’s 0.01 perm rating reduces moisture vapor transmission to near zero, helping prevent failure of moisture-sensitive flooring systems installed above it. What happens if I see "Pinholes" after application? Pinholes occur when air escapes the concrete as the epoxy cures. This is common on porous slabs and should be expected in some cases. If you see pinholes after your first coat, you must apply a second tight coat. A single pinhole can allow moisture vapor to pass through and eventually cause a failure in the finished flooring system. Can I use this as my final garage floor finish? No. VaporSolve LP is a functional industrial resin. It is not UV stable and is not designed for aesthetics. It must be covered with a pigmented epoxy, decorative flake system, or appropriate topcoat. Do I need to sand before my next coat? If you apply your next layer within the 12 to 24 hour recoat window, no sanding is required. If you wait longer than 24 hours, the surface becomes too hard for a chemical bond and must be sanded with 80–100 grit to create a mechanical profile. Can I use Pigmented VaporSolve LP directly on concrete? Pigmented VaporSolve LP is designed to be applied over VaporSolve Primer. If you are applying directly to properly prepared concrete without a primer, use the clear version. Why can't I split the kits into smaller batches? The mix ratio for moisture mitigation products must be exact to maintain the permeability rating. Measuring by eye or in small batches leads to errors. Even small mix inaccuracies can create weak spots that allow moisture to pass through, leading to system failure. Always mix the full kit as supplied.

APF VaporSolve® Primer | Adhesion Primer for Silicate Treated Concrete Product Overview APF VaporSolve® Primer is a specialized water based epoxy primer engineered exclusively for the VaporSolve moisture mitigation system. This product is not a standalone moisture vapor barrier (MVB). Its primary purpose is to serve as the critical "bridge" between challenging concrete substrates and the protective moisture barrier coat. It is specifically designed to solve adhesion failures on concrete slabs treated with silicate based curing compounds or densifiers—surfaces where traditional epoxy primers simply cannot bond. When used as the foundation for VaporSolve LP, it ensures the entire system remains anchored even under extreme hydrostatic pressure and high alkalinity. IMPORTANT: APF VaporSolve® Primer is an adhesion promoter, not a moisture barrier. It must be topcoated with VaporSolve LP to achieve moisture mitigation. Do not purchase this as a standalone solution for moisture vapor; it is specifically for bonding to high moisture slabs and concrete treated with silicates or densifiers. Where This Product Fits System Foundation: The mandatory first coat for the VaporSolve moisture mitigation system. Silicate Bond Specialist: Formulated to penetrate concrete treated with sodium or potassium silicates. Damp Slab Integration: Safely adheres to green or damp concrete where solvent primers fail. Alkalinity Defense: Uses Bisphenol F resin technology to resist the high pH environments common in wet slabs. Key Features Substrate Penetration: Low viscosity allows the resin to wet out and anchor into dense concrete pores. System Specific: Engineered to work in perfect chemical harmony with VaporSolve LP. Water Based & Low Odor: Safe for use in schools, hospitals, and occupied residential spaces. Wide Application Window: Reliable curing in temperatures ranging from 40°F to 100°F. Technical Specs & Mixing Property Details Coverage Approximately 200 sq ft per gallon Mix Ratio Do not mix partial kits Water Addition 1 gal water (3 gal kit) | 1 qt water (0.75 gal kit) Next Step Apply VaporSolve LP within 24 hours Surface Preparation Concrete must be mechanically prepared to a CSP 2 or CSP 3 profile. Remove all wax, old coatings, and loose contaminants. Vacuum thoroughly; the primer must reach the open pores of the concrete. Important: Acid etching is not an approved prep method for moisture mitigation systems. Mixing Instructions Pour entire contents of Part B into Part A. Mix for 2 to 3 minutes with a low speed drill (300 to 450 RPM). Add Water: Add the required amount of clean potable water and mix again for 2 to 3 minutes until uniform and creamy. Apply immediately. Pour material onto the floor within 3 minutes of mixing to maximize penetration. Frequently Asked Questions Can I skip the primer and just use VaporSolve LP?If your concrete has been densified or treated with silicates, skipping this primer will likely lead to a bond failure. This primer is the only layer engineered to bite into those silicate residues. How long do I wait before applying the VaporSolve LP barrier coat?Apply the LP barrier coat as soon as the primer is tack free, typically within 6 to 12 hours. Do not wait longer than 24 hours without mechanical sanding. Is this the same as a standard water based epoxy?No. This is a Bisphenol F resin system designed specifically for the extreme alkalinity and vapor pressure found in moisture mitigation environments. Does this primer come in colors?No. VaporSolve Primer is a clear system. Its job is substrate penetration, not aesthetics. Color is introduced in the subsequent coating layers. Do I need to wash the floor before priming?Mechanical grinding is the best prep. If the slab is dirty, it must be degreased and neutralized before grinding. The primer must reach clean, open concrete to work.

AQUALAB Pure Gloss | Water Based Urethane Epoxy Topcoat Product Overview AQUALAB Pure Gloss is a high performance, aliphatic water based urethane topcoat engineered to provide a professional grade protective shield over epoxy flooring. This two component (5 to 1) system delivers superior chemical resistance, elite abrasion resistance, and long term UV protection while maintaining a low odor application. This is the definitive choice for installers who need to protect warehouse and light duty commercial epoxy floors from premature wear, staining, and UV damage. The Aliphatic Advantage: Why Use a Urethane? While epoxy provides the structural build and "pop" for decorative floors, it is naturally susceptible to micro scratches and chemical staining. AQUALAB Pure Gloss adds an aliphatic urethane layer that is significantly harder and more resilient than epoxy. This is why most professional systems use a urethane or polyaspartic topcoat instead of leaving epoxy exposed. This results in: Extreme Scratch Resistance: Drastically reduces the "dulling" effect of foot traffic. UV Shielding: Unlike standard epoxy, this topcoat will not yellow and helps slow down the ambering of the epoxy layers beneath it. Stain Protection: Creates a non-porous surface that is much easier to clean and maintain in residential or commercial settings. Finish Options Gloss: Delivers a high-shine, glass like finish that maximizes color depth. Satin: Provides a refined, low-sheen look that hides surface imperfections and dust more effectively. Frequently Asked Questions Is this better than using epoxy as a topcoat?Yes. Aliphatic urethane topcoats provide significantly better chemical resistance, scratch resistance, and long term cleanability compared to standard epoxy alone. Does this product yellow?No. AQUALAB is non yellowing and contains UV inhibitors that help protect the underlying epoxy layers from direct sunlight. Can this be used indoors?Yes. The low odor, water based formulation is specifically designed for interior and occupied environments where solvent smells are not permitted. How many coats should I apply?We recommend two coats for the best durability and to ensure a perfectly uniform aesthetic finish across the entire floor. Can this be used over any epoxy?It is designed for use over properly prepared epoxy systems. If you are applying it over a different brand, we recommend a small adhesion test first. What is the mix ratio?The mix ratio is 5 parts Part A to 1 part Part B. Ensure you mix thoroughly for 2 to 3 minutes before application. What is the coverage rate?Coverage typically ranges from 500 to 600 square feet per kit on smooth surfaces and 400 to 500 square feet on partial flake epoxy floors. Can I add water to the mixture?No. Do not add water or solvents to the mixture. AQUALAB is formulated to be used exactly as it is packaged. How soon can I walk on the floor?The floor is typically ready for foot traffic after 24 hours of cure time at standard room temperatures. What is the best way to apply AQUALAB?Use the "dip and roll" method with a high-quality lint-free roller. This product is designed for dip and roll application rather than ribbon pour methods used with some other coatings.

Wooster Big Ben 18 inch Frame  Use with roller covers 18-inches long, all nap heights including 18In Pro-Grade Woven Shed-Resistant Roller Cover By Assurance Lightweight, extra strong frame that will not rust  Easy on and off epoxy roller cover installation, no loose hardware! When it comes to installing epoxy an 18in roller will save you time and effort! Whether its spreading out your resin or doing your back roll with polyaspartic having an 18in roller will allow you to complete your job faster!

Box Mixer, 5" diameter, 7-16" hex Shaft, 24" OAL The 5" Box Mixer is the mixing tool we recommend for achieving consistent, professional results with epoxy flooring systems. Specifically designed for high-viscosity materials, its football-shaped mixing head thoroughly blends epoxy resins, hardeners, and pigments to create a smooth, uniform mixture ready for application. Featuring a durable 7/16" hex shaft and a 24" overall length, this heavy-duty mixer helps minimize air entrapment while ensuring epoxy components are fully incorporated for optimal coating performance. Designed for High-Performance Epoxy Mixing Proper mixing is one of the most important steps in any epoxy flooring installation. The 5" Box Mixer efficiently circulates material throughout the bucket, thoroughly blending Part A, Part B, and pigments to eliminate unmixed material and reduce trapped air. The result is a smoother, more consistent coating that is easier to apply and performs as intended. Whether you're installing a solid color floor, metallic epoxy, flake system, primer, moisture vapor barrier, or topcoat, this mixer provides the consistency needed for professional-quality results. Key Features Football-Shaped Mixing Head: Designed to efficiently blend high-viscosity epoxy materials. Minimizes Air Entrapment: Helps reduce bubbles during mixing for smoother coating applications. Thorough Material Blending: Ensures epoxy components and pigments are evenly dispersed throughout the mixture. Heavy-Duty Construction: Built for repeated use on residential, commercial, and industrial flooring projects. 7/16" Hex Shaft: Provides a secure fit for compatible drills and reliable mixing performance. 24" Overall Length: Ideal for mixing materials in standard 5-gallon buckets. 5" Mixing Head: Optimized for blending epoxy coatings and other high-viscosity materials. Recommended Uses 100% solids epoxy coatings Epoxy primers Moisture vapor barrier (MVB) epoxies Metallic epoxy systems Full flake and partial flake flooring systems Polyaspartic coatings Mixing epoxy pigments and additives Specifications Mixing Head Diameter: 5" Shaft: 7/16" Hex Overall Length: 24" Recommended For: High-viscosity epoxy and resinous flooring materials Why We Recommend It The quality of any epoxy floor starts with proper mixing. The 5" Box Mixer is the preferred mixer for One Stop Epoxy coating systems because it helps produce a consistent, bubble-free mixture while reducing unmixed material. It's an essential tool for contractors and DIY installers looking to achieve professional-quality flooring results.

Cabin Fever Vinyl Flakes – 1/16" Flake Size (FB-127) Cabin Fever offers a warm, rustic blend of grays, creams, and soft whites designed to bring comfort and style to any epoxy floor. With a subtle contrast between earthy neutrals and a small accent of black, this flake blend delivers a lived-in look perfect for residential interiors, basements, and garage floors with character. It’s a popular choice for anyone wanting a finish that feels both grounded and welcoming. Cabin Fever Is Made Up Of: 30% Granite (F1410) – Light gray 30% Scone (F1780) – Beige-tan neutral 30% White (F1820) – Clean, soft white 10% Black (F1050) – Deep black accent Carefully balanced and UV-stable, Cabin Fever is part of Torginol’s Varicolored Flake series and delivers a finish that’s both inviting and durable. What Are Vinyl Flakes? Vinyl flakes are decorative aggregates used to enhance the look and feel of resin-based flooring systems. They add color, texture, and light slip resistance while increasing the visual impact of your epoxy floor. One Stop Epoxy supplies only UV-stable, precision-screened flakes for a clean, professional finish every time. Installing An Epoxy Flake Floor System For a 2-day full flake floor, broadcast Cabin Fever flakes into our Self-Leveling 100% Solids High Strength Epoxy – 3 Gallon Kit. For faster turnaround, use 150 Fast Cure 100% Solids Epoxy – Light Gray (For professional or highly experienced users only.) Seal a full flake system with PolyGloss 85 – 1, 2, and 3 Gallon Kits of Polyaspartic Seal a partial flake system with Urethane Gloss/Satin High Performance Epoxy Topcoat – 1 Gallon Recommended Uses Basement Garage Man Cave Interior Rooms Porch Restaurant Hotel Lobby Patio Locker Room Sports Bar Showroom Floor Kitchen High-Traffic Areas OneStopEpoxy.com where nationwide shipping on vinyl flakes is always free.