APF VaporSolve® Primer | Adhesion Primer for Silicate Treated Concrete Product Overview APF VaporSolve® Primer is a specialized water based epoxy primer engineered exclusively for the VaporSolve moisture mitigation system. This product is not a standalone moisture vapor barrier (MVB). Its primary purpose is to serve as the critical "bridge" between challenging concrete substrates and the protective moisture barrier coat. It is specifically designed to solve adhesion failures on concrete slabs treated with silicate based curing compounds or densifiers—surfaces where traditional epoxy primers simply cannot bond. When used as the foundation for VaporSolve LP, it ensures the entire system remains anchored even under extreme hydrostatic pressure and high alkalinity. IMPORTANT: APF VaporSolve® Primer is an adhesion promoter, not a moisture barrier. It must be topcoated with VaporSolve LP to achieve moisture mitigation. Do not purchase this as a standalone solution for moisture vapor; it is specifically for bonding to high moisture slabs and concrete treated with silicates or densifiers. Where This Product Fits System Foundation: The mandatory first coat for the VaporSolve moisture mitigation system. Silicate Bond Specialist: Formulated to penetrate concrete treated with sodium or potassium silicates. Damp Slab Integration: Safely adheres to green or damp concrete where solvent primers fail. Alkalinity Defense: Uses Bisphenol F resin technology to resist the high pH environments common in wet slabs. Key Features Substrate Penetration: Low viscosity allows the resin to wet out and anchor into dense concrete pores. System Specific: Engineered to work in perfect chemical harmony with VaporSolve LP. Water Based & Low Odor: Safe for use in schools, hospitals, and occupied residential spaces. Wide Application Window: Reliable curing in temperatures ranging from 40°F to 100°F. Technical Specs & Mixing Property Details Coverage Approximately 200 sq ft per gallon Mix Ratio Do not mix partial kits Water Addition 1 gal water (3 gal kit) | 1 qt water (0.75 gal kit) Next Step Apply VaporSolve LP within 24 hours Surface Preparation Concrete must be mechanically prepared to a CSP 2 or CSP 3 profile. Remove all wax, old coatings, and loose contaminants. Vacuum thoroughly; the primer must reach the open pores of the concrete. Important: Acid etching is not an approved prep method for moisture mitigation systems. Mixing Instructions Pour entire contents of Part B into Part A. Mix for 2 to 3 minutes with a low speed drill (300 to 450 RPM). Add Water: Add the required amount of clean potable water and mix again for 2 to 3 minutes until uniform and creamy. Apply immediately. Pour material onto the floor within 3 minutes of mixing to maximize penetration. Frequently Asked Questions Can I skip the primer and just use VaporSolve LP?If your concrete has been densified or treated with silicates, skipping this primer will likely lead to a bond failure. This primer is the only layer engineered to bite into those silicate residues. How long do I wait before applying the VaporSolve LP barrier coat?Apply the LP barrier coat as soon as the primer is tack free, typically within 6 to 12 hours. Do not wait longer than 24 hours without mechanical sanding. Is this the same as a standard water based epoxy?No. This is a Bisphenol F resin system designed specifically for the extreme alkalinity and vapor pressure found in moisture mitigation environments. Does this primer come in colors?No. VaporSolve Primer is a clear system. Its job is substrate penetration, not aesthetics. Color is introduced in the subsequent coating layers. Do I need to wash the floor before priming?Mechanical grinding is the best prep. If the slab is dirty, it must be degreased and neutralized before grinding. The primer must reach clean, open concrete to work.

One Stop WB Epoxy Primer | High Performance 2 Part Water Based Epoxy One Stop WB Epoxy Primer is a professional grade water based epoxy designed to create a high bond foundation for epoxy flooring systems. This product is most commonly used as a pore sealing primer under 100% solids epoxy, where controlling outgassing and ensuring adhesion is critical to the success of the entire floor. Universal Compatibility – Approved for use with One Stop 100% Solids, 150FC, Metallic Dream, WB Urethanes, and PolyGloss 85. Multi Purpose Utility – Functions as a high bond primer, a flake floor base coat, or a durable interior finish coat. Pore Sealing Technology – Eliminates outgassing bubbles so your next layer of 100% solids Epoxy goes out bubble free. Industrial Strength – Scratch and abrasion resistant; tough enough for vehicle traffic and commercial use. VOC Compliant – Safe for interior use in garages, kitchens, warehouses, and basements. Most coating failures start at the surface. A properly applied primer like this one eliminates that risk by sealing the concrete and creating a consistent foundation for the system. Where This Product Fits in Your System This primer is designed to work as the first step in a complete epoxy flooring system. Use under 100% solids epoxy base coats Use before Flake or Quartz Systems to improve adhesion Can be used as a standalone coating in light duty applications This is not just a primer. It is the foundation that determines how well your entire system performs. Mixing and Application Instructions Step 1 Pre Mix Because this is a water based product, settlement is normal and expected. Blend the bucket of BASE (Part A) for 1 minute before pouring into a larger bucket and combining with activator. Step 2 The Blend For 1 Gallon Kits: Pour Part A and Part B into a larger mixing bucket and blend for 2 minutes using a paddle mixer. For 2 or More Gallons: When mixing multiple kits together (up to 4 gallons in a 5 gallon bucket), you must use a Box Mixer and blend for 2 - 3 minutes to ensure a complete chemical reaction. Step 3 Application Pour the mixed material directly onto the floor. While wearing spiked shoes, spread the material evenly using a flat squeegee. Small Projects: You may utilize a paint tray and dip and roll using a 1/4” nap epoxy roller (ensure the roller is de-shedded prior to use). To avoid roller lines, you may backroll the floor before the product becomes tacky. Coverage and Technical Specs All SFPG dependent upon porosity of the concrete: Primer on Porous Concrete: 200 to 250 SFPG Grind and Seal Base Coat: 200 to 250 SFPG Grind and Seal Body Coat: 150 to 200 SFPG Light Duty DIY Garage Floor (Needs Pigment and Two Layers): 150 to 175 SFPG Concrete Sealer / Dust Proofing: 200 to 250 SFPG Densifier Application: When applying to very soft or weak concrete, add 10% water to the first coat and apply as a densifier. The material should be applied to saturate the surface and allow for proper penetration into the concrete. Coverage rates for this application will vary depending on the condition and porosity of the concrete. Once the densified layer has dried, apply a second full strength coat without dilution. This exception applies only when using the product as a densifier and does not apply to standard primer or coating applications. Application Temp: Best if applied between 55 and 90 degrees Fahrenheit. Cure Schedule and Recoating Tack Free / Foot Traffic: 12 Hours Recoat Window: 24 Hours Heavy Foot Traffic: 48 Hours Vehicular Traffic: 72 Hours (3 Days) When To Sand For Additional Coats: A second coat may be applied within the 24 hour recoat window without sanding. If more than 24 hours have passed since the previous application, sanding is required. Sand the surface using a 100 to 120 mesh sanding screen, then vacuum and wipe the surface with denatured alcohol or acetone to achieve a proper mechanical bond before applying the next coat. Frequently Asked Questions Can I add a little water to make the primer spread further?No. You should not thin to expand coverage rate. Thinning disrupts the chemical bond and will result in a weak coat. The only exception is adding 10% water when using the product strictly as a densifier for very soft, crumbly concrete. Why do I have to sand before applying my metallic or topcoat?Sanding creates a mechanical profile or "teeth" for the next layer to grab onto. Skipping this step leads to poor adhesion and potential delamination. Which mixer should I use?For single gallon kits, a standard paddle mixer is fine. For anything 2 gallons or larger, a Box Mixer is required to ensure the Part A and Part B are fully integrated without trapping excessive air. Do I need a primer before epoxy?Yes. A primer improves adhesion, seals concrete pores to reduce outgassing, and helps prevent bubbles in your high build layers. Can I use this under metallic epoxy?Yes. This is one of the best applications for this product as it ensures the Metallic Dream layer goes down over a sealed surface, preventing bubbles from ruining the finish. Is this a high build coating?No. Water based epoxy is typically used as a primer or light duty coating, not as a high build system. Can this be used as a final coat?Yes, in light duty environments such as storage areas or mechanical rooms. What happens if I skip sanding between coats?Skipping sanding can lead to poor adhesion and potential delamination between layers of the flooring system.

Moisture Vapor Barrier Epoxy | 25 lb Rated 100% Solids MVB One Stop Epoxy 100% Solids Moisture Vapor Barrier Epoxy is a professional-grade foundation coating engineered to block moisture vapor transmission through concrete slabs. Rated for extreme conditions up to 25 lbs of moisture vapor emission, this product creates a permanent barrier that prevents the most common causes of floor failure: peeling, bubbling, and delamination. This is not a finish coat or a receiver coat. It is a critical insurance policy used to stabilize concrete before installing a 100% solids epoxy build system. Why Professionals Use a 25 lb Rated MVB Concrete is naturally porous and acts like a sponge, releasing moisture vapor for years. When this vapor pressure builds up beneath a standard coating, it physically breaks the bond, leading to total system failure. Our MVB Epoxy solves this by penetrating deep into the concrete capillaries to create a structural seal that can handle high hydrostatic pressure. Extreme Moisture Resistance: Rated to block up to 25 lbs of vapor transmission—far exceeding standard epoxies. Prevents Osmotic Blistering: Stops the bubbles that form when moisture is trapped under the floor. Superior Bond Strength: Provides a stabilized, non-porous surface for your next epoxy layer to lock onto. Zero VOC Formulation: 100% solids with no odor, making it safe for interior and basement applications. The Proper System Sequence To ensure a lifetime bond on slabs with moisture concerns, follow the professional "Step-Up" method: The Barrier: Apply One Stop MVB Epoxy directly to mechanically profiled concrete (CSP 2-3). The Build Coat: Once cured, apply a layer of 100% Solids Self Leveling Epoxy. This acts as your pigmented base or "receiver coat" for flakes. The Finish: Complete the system with a high-performance Polyaspartic or Urethane topcoat. Mixing and Application Requirements Pro Tip: Do not broadcast flakes or quartz directly into the MVB. This material must be applied as a continuous, unbroken film to effectively block moisture. Mix for a full 3 minutes to ensure the chemical barrier is fully cross-linked. Mix Ratio: 2 Parts A to 1 Part B. Mixer: Use a box or cage style mixer at 300 to 450 RPM. Coverage: 100 to 150 square feet per gallon depending on porosity. Dry Time: 8 to 10 hours at room temperature. Frequently Asked Questions Do I need a moisture vapor barrier epoxy?If moisture is present, unknown, or if you are installing over a slab on grade, this is a necessary preventative step to avoid total coating failure. How do I know if my concrete has a moisture problem?Visible signs include efflorescence (white powder) or dark spots. The only certain way is testing, but applying MVB is the safest preventative measure for any slab where the history is unknown. Can I use this for basement floors?Yes. Basements are inherently prone to moisture issues. Using this vapor barrier is the best way to ensure your basement epoxy floor never peels or bubbles. Can I broadcast flakes directly into the MVB?No. The Moisture Vapor Barrier must be applied as a clean, continuous film to seal the slab. After it cures, you apply a 100% solids epoxy layer to serve as your pigmented receiver coat for flakes. Is this required for garage floors?It is highly recommended in humid environments, on older slabs, or if you are a professional installer offering a long-term warranty to your clients. What happens if I skip this step?Skipping moisture control on a high-vapor slab leads to osmotic blistering and total system delamination, requiring a costly total replacement. Can this be used as a finished floor?No. This is a functional base layer designed to stabilize the slab. It must be covered by a 100% solids epoxy build coat and an appropriate topcoat. What should I use over this product?Typically, installers follow this with a 100% solids epoxy (like our Self Leveling or 150 Fast Cure) before moving to their decorative broadcast or topcoat. How long do I have to wait before applying my next coat?The material is generally dry to the touch in 8 to 10 hours. You should apply your next coat of epoxy within 24 hours to ensure a strong chemical bond. What is the mix ratio?The mix ratio is 2 parts Part A to 1 part Part B. Mix thoroughly with a drill mixer for a full 3 minutes before pouring.

Premera FP1 Fusion Primer Premera FP1 Fusion Primer is a cutting-edge, fast-drying nano-adhesive primer designed to bond seamlessly to nearly any contaminate-free hard surface. Its unique formulation creates a molecular bridge between coatings and substrates, allowing coatings that would typically struggle to adhere to form a strong, durable bond. This molecular bonding eliminates the need for time-consuming sanding or mechanical abrasion, drastically streamlining your application process and reducing preparation time. Why Premera FP1 Can Replace Mechanical Abrasion: Traditionally, surface preparation requires mechanical abrasion like sanding or grinding to roughen the surface, ensuring that the new coating can properly bond. Premera FP1 Fusion Primer uses advanced nanotechnology to form covalent bonds at the molecular level. These bonds penetrate deep into the substrate, anchoring the coating firmly to the surface without needing to roughen it first. In plain English, this means that instead of having to sand down or grind a concrete or metal surface, Premera FP1 chemically fuses to the surface, creating a strong connection. This not only saves time but also preserves the integrity of the substrate by avoiding potential damage that mechanical abrasion can cause. Premera FP1 allows you to move straight to the next layer without compromising on adhesion quality. Key Features Of Premera FP1 Fusion Primer: No need for sanding or mechanical abrasion: Streamlines preparation while maintaining superior bonding. Strong bonding: Works even on the hardest-to-bond surfaces, including smooth metals. Fast drying: Quick adhesion promoter for efficient application. Covalent bonding: Bonds at the molecular level, becoming one with the surface. Versatile use: Suitable for almost any substrate, including concrete, steel, wood, tile, and fabric. Virtually invisible: Leaves no visible residue after application. Moisture and stain resistance: Protects from within, reducing future maintenance costs. Long-lasting protection: Extends the life of the substrate, protecting it from environmental wear and tear. Typical Uses of Premera FP1 Fusion Primer Adhesion layer: Bonds coatings to substrates or between two coatings, ensuring a durable finish. Substrate variety: Works on painted or unpainted iron, aluminum, copper, stainless steel, powder-coated surfaces, galvanized surfaces, concrete, wood, rubber, plastic, fiberglass, and glass. Ideal for Concrete Coatings: For professionals in the concrete coatings industry, Premera FP1 Fusion Primer provides a faster, more efficient way to achieve a perfect bond, especially when used in conjunction with one of our or our popular metallic flooring kits. By eliminating the need for mechanical abrasion, it reduces preparation time while ensuring high-quality results. To see just how easy the application process is watch this short YouTube video on the application process.

Premera Easy MVB Premera EasyMVB is a unique surface treatment for concrete consisting of specialized reactive chemicals in a colloidal silica matrix. EasyMVB can be used as a concrete treatment to penetrate into concrete and creates a moisture vapor barrier within concrete by reacting with and sealing pores and capillaries, eliminating vapor transmission and solving hydrostatic pressure challenges. EasyMVB is also a complementary pre-primer treatment for Premera’s sol-gel based products. When used in combination with Premera FP1 Fusion Primer, up to 25 lbs of moisture vapor can be withstood, effectively eliminating adhesion issues caused by moisture vapor. When applied to concrete or any pozzolanic material, Premera EasyMVB penetrates to seal, densify and thereby harden cementitious surfaces. Premera EasyMVB is formulated to penetrate and block capillaries by reacting with free calcium hydrates to form an insoluble, permanent barrier. It effectively eliminates efflorescence, improves water resistance, water repellency, and surface properties of cementitious materials. Premera EasyMVB is recommended for use as a pre-priming surface treatment on floorings, liners in immersion application, and adhered waterproofing membranes – including structures under hydrostatic pressure. Premera EasyMVB may be used as a standalone surface treatment in certain applications. Features: Environmentally friendly, zero VOC Blocks up to 25 lbs of hydrostatic pressure Prevents efflorescence from occurring Can polish concrete after HLT is usedReduces risk of moisture out-gassing, pin-holing, and blisters in top coats