150 Fast Cure 100% Solids Epoxy | Primer, Base Coat & MVB One Stop Epoxy 150 Fast Cure (150FC) is a contractor grade, rapid-curing 100% solids epoxy engineered specifically for high-efficiency broadcast systems. This versatile resin functions as a primer, base coat, and Moisture Vapor Barrier (MVB) in a single application, allowing crews to complete full flake, quartz, and sand broadcast floors in a fraction of the time. Designed for one day floor installations, 150FC performs exceptionally well in hot and humid environments, offering a rapid return to service without the "flash cure" risks of inferior fast-setting epoxies. The 150FC Technical Advantage 3-in-1 System: Acts as a high-strength primer, pigmented base coat, and MVB rated up to 12 lbs. 90-Minute Recoat: Fast cure profile allows for scraping and top coating in as little as 90 minutes in warmer temperatures. Extended Working Time: Provides 20 to 30 minutes of open time on the floor nearly double that of traditional rapid cure epoxies. UV Considerations: Engineered for full broadcast systems (flake, quartz, sand) where the epoxy is fully covered to prevent visible ambering. Best Uses for Fast Cure Epoxy One Day Flake Floors: The industry standard for rapid garage and commercial prep. Sand & Quartz Broadcasts: Ideal for industrial non-slip systems requiring fast turnaround. Humid Climates: Specifically formulated to remain manageable in high-humidity markets like Florida. Mixing and Application (Critical for Success) Pro Warning: 150FC is for experienced installers. It requires mechanical surface prep (CSP 2-3) and must be poured in ribbons immediately after mixing to avoid exotherm in the bucket. Mix Ratio: 2 Parts A to 1 Part B. Mix Time: 2 minutes if above 75°F; 3 minutes if below 75°F. Mixer: Use a box or cage style mixer for full kits. Working Time: 20–30 minutes depending on ambient temperature. Frequently Asked Questions Is this a good epoxy for garage floors?Yes. It is the preferred base coat for professional installers performing one day full flake garage floor installations. What makes 150FC different from other fast cure epoxies?150FC includes a built-in moisture vapor barrier (up to 12 lbs) and offers significantly more working time on the floor than standard rapid-set resins. Can I use this for a one day flake floor?Yes. This is the primary use for 150FC. Its fast cure profile allows you to prep, base, flake, and topcoat in a single shift. Why can’t this be used for solid color floors?Because 150FC is a fast-cure aromatic epoxy, it will amber under UV exposure. It must be used in a broadcast system where it is completely covered by flakes, sand, or quartz. Is this product beginner friendly?No. 150FC is designed for experienced contractors who understand how to manage fast-curing materials and jobsite pacing. Does this replace a moisture vapor barrier?Yes. It is rated to block moisture vapor transmission up to 12 lbs, eliminating the need for a separate MVB primer step. How long does 150FC take to dry before I can topcoat?Depending on temperature and humidity, you can typically sweep, vacuum, and topcoat in as little as 90 minutes. What is the working time for this fast cure epoxy?Depending on temperature, you will have between 20 and 30 minutes of working time once the material is poured onto the floor. Can 150FC be used outdoors?Yes, provided it is part of a full broadcast system where the epoxy is entirely covered and protected from UV exposure. Do I need to add solvent to thin this product?No. This is a true 100% solids epoxy. Adding solvents will compromise the cure and the moisture vapor barrier rating.

Full Flake Epoxy Flooring System – Durable, Customizable, Professional Results Transform your floors with the Full Flake Epoxy Flooring System, the ultimate solution for durable, customizable, and visually stunning epoxy floors. Whether for residential garages, commercial showrooms, or industrial warehouses, this system combines the superior performance of One Stop Epoxy Brand 100% Solids Epoxy, Vinyl Flakes, and Poly Gloss 85 Seal Coats to deliver unmatched durability, aesthetics, and protection. Why Choose the Full Flake Epoxy Flooring System? Durable & Long-Lasting: Withstands heavy traffic, chemicals, and abrasion. Customizable Finish: Decorative 1/4-inch flakes for a slip-resistant, visually appealing surface. Flexible Application Options: Choose from two base coat types for standard or quick installations. Premium Polyaspartic Seal Coats: Industry-leading protection with UV stability and scratch resistance. Low Maintenance: Easy to clean and maintain, reducing upkeep costs. Base Coat Options 100% Solids High-Strength Epoxy Designed for strength and durability. 3% Osmotic Vapor Resistance for industry-standard moisture protection. Dry Time: 8 hours at 75°F. Best for longer curing times and beginner installers. 150 Fast Cure Epoxy (FOR PROFESSIONAL USE ONLY) 12% Osmotic Moisture Vapor Resistance for superior moisture protection. Dry Time: 4 hours at 75°F. Perfect for experienced installers and time-sensitive projects. Decorative Flake Application Broadcast 1/4-inch decorative flakes at a rate of 1 pound per 8 square feet to create a textured, slip-resistant surface. Choose from a wide range of colors to achieve your desired look. Seal Coat Options – PolyGloss 85 Series PolyGloss 85 Slow Go (User Friendly) Extended working time: 60+ minutes. Ideal for large areas or novice installers. PolyGloss 85 (For Professional Use Only) 22 Minutes working time. Quick curing: Foot Traffic in 2 hours Vehicle traffic in 24 hours. Perfect for projects requiring fast turnaround. Applications This versatile system is perfect for: Residential Garages Commercial Showrooms Retail Spaces Industrial Warehouses Outdoor Patios Hands On Epoxy Training Ready to enhance your skills? Join our hands-on epoxy flooring classes in Orlando, Florida right by Orlando International airport and minutes from ALL the attractions. Held every 4–6 weeks, these courses are perfect for new installers and industry professionals looking to refine their techniques.

LABPOX 30 100% Solids Epoxy | Professional Flooring System LABPOX 30 is a professional grade, 100% solids epoxy engineered for installers who demand reliability and extended working time. Whether used as a base coat, body coat, or the foundation for metallic epoxy systems, LABPOX 30 delivers the consistency required for high performance industrial, commercial, and residential environments. The Professional Advantage: Unlike limited use epoxies that flash quickly, LABPOX 30 provides a balanced 45 to 60 minute working window, ensuring superior flow, pinhole mitigation, and a glass like finish even on large scale installations. Technical Performance Snapshot Property ASTM Standard / Value Mix Ratio 2 Parts A to 1 Part B Compressive Strength 13,000 psi Tensile Strength 8,500 psi Shore D Hardness 82 Elongation 14 percent VOC Content 9 to 10 g per L (Low VOC) Pot Life (72°F) 50 minutes Where LABPOX 30 Fits in a Flooring System 1. As a High Adhesion Base Coat Provides a consistent, durable foundation for solid color, flake, or quartz broadcast systems. LABPOX 30 is self priming and can be applied directly to properly prepared concrete under the right conditions. 2. As a Metallic Body Coat ("The Money Coat") Specifically optimized for metallic epoxy systems. The extended open time allows for intricate pigment movement and pattern development before the resin sets. 3. As an Intermediate Build Coat Increases overall system thickness and impact resistance in heavy traffic industrial or warehouse environments. Approximate Coverage Rates Application Type Square Feet Per Gallon (SFPG) Metallic Body Coat 50 SFPG Metallic Base Coat 80 to 135 SFPG Vinyl Flake Receiver Coat 133 to 150 SFPG Commercial/Industrial Solid Color 80 to 133 SFPG LABPOX 30 vs. Typical 100% Solids Epoxy Why professional installers choose LABPOX 30 over standard alternatives: Pinhole Mitigation: Advanced technology reduces surface defects by up to 98 percent in pre tinted versions. Extended Control: 60 minutes of working time vs. the standard 20 to 30 minutes of typical epoxies. Chemical Resistance: Superior resistance to amine blush and common site contamination. Cure Schedule (At 72°F) Working Time: 60 Minutes Tack Free: 9 Hours Recoat Window: 9 to 24 Hours Foot Traffic: 24 Hours Full Chemical Cure: 7 Days System Limitations LABPOX 30 requires a dry substrate. Moisture content must be below acceptable limits unless a moisture mitigation system is used. Not intended for exterior applications. Recommended System Setup For a guaranteed bond and long term finish, follow this professional stack: Primer: LAB Surface Epoxy Primer or LABPOX MVB Clear Fast for moisture vapor barriers. Base/Body: Apply LABPOX 30 (Solid Color or Metallic). Topcoat: Seal with LABFAST Xtra Time (Polyaspartic) or LABFENDER Polyurethane for maximum abrasion resistance. Mixing and Application Requirements Application Equipment 1/8 inch notched rubber squeegee 3/8 inch nap woven shed resistant roller cover 3 inch chip brush Mixing Instructions Precision in the mixing process is critical to ensure the chemical bond and structural integrity of the LABPOX 30 system. Combine Components: Pour 2 containers of Part A (Base) into a large mixing bucket, being careful not to pour material onto the sides of the larger bucket. Add Activator: Pour the Part B (Activator) directly into the center of the large bucket. Again, ensure no material gets on the sides of the Base bucket; failing to do so may leave unmixed resin that causes soft spots on your finished floor. Mixing Time: Mix full kits with a Box mixer for 2 minutes. Use a low-speed drill (300 to 450 RPM) to minimize air entrapment. Scrape Sides: During the mixing process, make sure to scrape the sides and bottom of the mixing container thoroughly so no unmixed material remains. Immediate Placement: Once the product is properly mixed, it needs to be immediately poured onto the floor. Leaving mixed material for too long in a mixing pail will create an exothermic reaction (rapid heat buildup), rendering the product unusable. Application Procedure Application Procedure Pour mixed material in a 20 foot long 12 inch wide ribbon Do not drain or scrape remaining material from the bucket onto the floor. Spread to uniform thickness with a notched squeegee and roll North South and back roll East West to achieve uniform coverage. Roller should be a 3/8 inch shed resistant epoxy roller cover. PRO TIP: For metallic floors, use the extended 60 minute window to manipulate your pigments with a 9/16 inch looped roller or notched squeegee to create depth and movement before the product begins its initial set. Frequently Asked Questions Is LABPOX 30 good for metallic epoxy floors?Yes. It is exceptionally well suited for metallic systems due to its 45 to 60 minute working time and excellent flow characteristics, allowing installers to create flawless designs with proper pigment movement. Can this be used as a base coat?Yes. LABPOX 30 works incredibly well as a dependable, high strength base coat for a wide variety of systems, including solid color, flake, and quartz. Is this product beginner friendly?Because of the extended working time, it is more forgiving than fast cure epoxies, but proper surface preparation and installation technique are still required. How long is the actual working time?You will have approximately 60 minutes of working time at 70°F and 45 minutes at 80°F. Humidity and surface temperature can also affect these windows. What is the mix ratio for LABPOX 30?It is a two component system with a precise mix ratio of 2 Parts A to 1 Part B (2A:1B) by volume. Can this be used for flake floors?Absolutely. It performs as a reliable receiver coat for broadcast flake systems, providing enough open time to ensure a consistent flake distribution. Why is the "Extended Working Time" so important?Standard epoxies can flash quickly in the bucket, leading to stress and mistakes. LABPOX 30 gives you a massive window to maintain a wet edge on large floors and execute intricate metallic designs without the product locking up prematurely. Does this require a topcoat?Yes. Like all 100 percent solids epoxies, a UV stable topcoat (like Polyaspartic or Urethane) is highly recommended to prevent ambering and provide long term scratch resistance.

Moisture Vapor Barrier Epoxy | 25 lb Rated 100% Solids MVB One Stop Epoxy 100% Solids Moisture Vapor Barrier Epoxy is a professional-grade foundation coating engineered to block moisture vapor transmission through concrete slabs. Rated for extreme conditions up to 25 lbs of moisture vapor emission, this product creates a permanent barrier that prevents the most common causes of floor failure: peeling, bubbling, and delamination. This is not a finish coat or a receiver coat. It is a critical insurance policy used to stabilize concrete before installing a 100% solids epoxy build system. Why Professionals Use a 25 lb Rated MVB Concrete is naturally porous and acts like a sponge, releasing moisture vapor for years. When this vapor pressure builds up beneath a standard coating, it physically breaks the bond, leading to total system failure. Our MVB Epoxy solves this by penetrating deep into the concrete capillaries to create a structural seal that can handle high hydrostatic pressure. Extreme Moisture Resistance: Rated to block up to 25 lbs of vapor transmission—far exceeding standard epoxies. Prevents Osmotic Blistering: Stops the bubbles that form when moisture is trapped under the floor. Superior Bond Strength: Provides a stabilized, non-porous surface for your next epoxy layer to lock onto. Zero VOC Formulation: 100% solids with no odor, making it safe for interior and basement applications. The Proper System Sequence To ensure a lifetime bond on slabs with moisture concerns, follow the professional "Step-Up" method: The Barrier: Apply One Stop MVB Epoxy directly to mechanically profiled concrete (CSP 2-3). The Build Coat: Once cured, apply a layer of 100% Solids Self Leveling Epoxy. This acts as your pigmented base or "receiver coat" for flakes. The Finish: Complete the system with a high-performance Polyaspartic or Urethane topcoat. Mixing and Application Requirements Pro Tip: Do not broadcast flakes or quartz directly into the MVB. This material must be applied as a continuous, unbroken film to effectively block moisture. Mix for a full 3 minutes to ensure the chemical barrier is fully cross-linked. Mix Ratio: 2 Parts A to 1 Part B. Mixer: Use a box or cage style mixer at 300 to 450 RPM. Coverage: 100 to 150 square feet per gallon depending on porosity. Dry Time: 8 to 10 hours at room temperature. Frequently Asked Questions Do I need a moisture vapor barrier epoxy?If moisture is present, unknown, or if you are installing over a slab on grade, this is a necessary preventative step to avoid total coating failure. How do I know if my concrete has a moisture problem?Visible signs include efflorescence (white powder) or dark spots. The only certain way is testing, but applying MVB is the safest preventative measure for any slab where the history is unknown. Can I use this for basement floors?Yes. Basements are inherently prone to moisture issues. Using this vapor barrier is the best way to ensure your basement epoxy floor never peels or bubbles. Can I broadcast flakes directly into the MVB?No. The Moisture Vapor Barrier must be applied as a clean, continuous film to seal the slab. After it cures, you apply a 100% solids epoxy layer to serve as your pigmented receiver coat for flakes. Is this required for garage floors?It is highly recommended in humid environments, on older slabs, or if you are a professional installer offering a long-term warranty to your clients. What happens if I skip this step?Skipping moisture control on a high-vapor slab leads to osmotic blistering and total system delamination, requiring a costly total replacement. Can this be used as a finished floor?No. This is a functional base layer designed to stabilize the slab. It must be covered by a 100% solids epoxy build coat and an appropriate topcoat. What should I use over this product?Typically, installers follow this with a 100% solids epoxy (like our Self Leveling or 150 Fast Cure) before moving to their decorative broadcast or topcoat. How long do I have to wait before applying my next coat?The material is generally dry to the touch in 8 to 10 hours. You should apply your next coat of epoxy within 24 hours to ensure a strong chemical bond. What is the mix ratio?The mix ratio is 2 parts Part A to 1 part Part B. Mix thoroughly with a drill mixer for a full 3 minutes before pouring.