1 Quart Containers Ensure precise epoxy measurements with our 1-quart mixing cups. These cups provide an ideal solution for accurate proportioning and thorough mixing of epoxy components. With a capacity of 1 quart (32 ounces), these cups can accommodate larger epoxy projects while maintaining precise ratios. The clear measurement markings on the cups make it easy to achieve the perfect mix every time. Our 1-quart mixing cups are chemical-resistant and can withstand the demands of epoxy mixing. Simplify your epoxy projects and achieve consistent results with our reliable and convenient 1-quart mixing cups.

Shed-resistant woven fabric reduces roller shed for a smooth finish The 1/4" nap is best suited for smooth surfaces and even application of top coats A rugged design offering double-thick polypropylene core resists cracks, solvents, and water Compatible with One Stop Epoxy Polyaspartics, Polyurethanes, and Epoxy Coatings  Offered in 18" and 9"

12 oz Non-slip Epoxy Top Coat Additive A 12 oz non-slip epoxy top coat additive is a product that can be added to epoxy coatings to enhance their slip resistance. It is designed to provide a textured surface that reduces the chances of slips and falls, especially in areas prone to wet or slippery conditions.  Coarse - 20 Grit Fine - 100 Grit

150 Fast Cure 100% Solids Epoxy for One Day Full Broadcast Floors One Stop Epoxy 150 Fast Cure, commonly called 150FC, is a rapid cure 100% solids epoxy built specifically for full broadcast flooring systems. It is designed for full flake, quartz, sand, and other approved broadcast floors where the wet epoxy is completely covered with decorative or functional media. 150FC can perform three jobs in one application: primer, pigmented receiver coat, and moisture vapor barrier rated up to 12 lbs. This allows experienced installers to mechanically prepare the concrete, apply one epoxy layer, complete the broadcast, and move toward the topcoat without installing a separate primer or moisture vapor barrier when slab conditions are within the published product limits. At 75 degrees Fahrenheit, 150FC provides approximately 25 minutes of working time on the floor. Under a full broadcast, it cures in approximately 2 hours at 75 degrees Fahrenheit and can cure in as little as approximately 75 to 90 minutes in very warm conditions. Free shipping to the 48 contiguous states, and most orders ship out the same or next business day. Quick Answer: 150FC is a fast cure 100% solids epoxy for experienced installers building full broadcast floors. It combines a primer, pigmented receiver coat, and moisture vapor barrier rated up to 12 lbs in one application. Working time is approximately 25 minutes at 75 degrees Fahrenheit, and full broadcast floors can be ready for scraping and topcoating in approximately 2 hours at 75 degrees Fahrenheit or faster in warmer conditions. NOT FOR BEGINNERS 150FC is designed for experienced epoxy installers who understand fast cure materials, crew coordination, mixing, placement, broadcast timing, and jobsite temperature. Once Part A and Part B are combined, the installation moves quickly. If you are learning how to install epoxy flooring, use a slower and more forgiving epoxy system. What 150FC Is Built to Do 150FC is not intended to be a general purpose epoxy. Its strength is combining fast cure, full broadcast capability, and moisture vapor protection into a single resin layer. Application How 150FC Is Used Full Flake Floors Used as the pigmented receiver coat before broadcasting vinyl flakes to rejection. This is one of the primary uses for 150FC. Quartz Broadcast Floors Used as the resin layer that receives a full quartz broadcast in commercial and decorative flooring systems. Sand Broadcast Floors Receives a full sand broadcast where texture, additional build, or another resinous flooring layer is required. Other Approved Broadcast Media May be used with approved broadcast aggregate such as aluminum oxide when the complete flooring system calls for it. Moisture Vapor Control Provides moisture vapor resistance up to the published 12 lb rating when slab conditions and installation requirements are within the product limits. For a complete flake package with epoxy, vinyl flakes, and topcoat already matched to the floor size, see our Full Flake Epoxy Flooring Systems. Where 150FC Should Not Be Used 150FC must be buried beneath a complete broadcast. It is not the correct epoxy when the base coat itself will remain visible. Application Use 150FC? Full Flake Broadcast Yes Full Quartz Broadcast Yes Full Sand Broadcast Yes Partial Flake Floor No Solid Color Floor No Metallic Epoxy Base Coat No Exposed Epoxy Finish No 150FC is not UV stable and will amber when exposed to light. In a true full broadcast system, the epoxy is completely covered by vinyl flakes, quartz, sand, or another approved media before the clear wear coat is installed. That keeps the epoxy itself from remaining visible. For solid color floors, partial flake floors, and other applications where the epoxy remains visible, use our Self Leveling 100% Solids Epoxy instead. Why 150FC Works for One Day Full Flake Floors A traditional epoxy installation may require separate primer, epoxy, broadcast, cure, and topcoat stages spread across multiple days. 150FC is designed to compress that sequence. Mechanically prepare the concrete. Apply 150FC as the primer, moisture vapor control layer, and pigmented receiver coat. Broadcast the vinyl flakes, quartz, or sand to rejection while the epoxy remains wet. Allow the fast cure epoxy to harden. Scrape and vacuum the cured broadcast surface. Apply the specified clear topcoat. When the floor, temperature, crew, and complete system are appropriate, this sequence allows experienced installers to complete many full broadcast floors in one day. Working Time Changes With Temperature 150FC is fast, but it provides meaningful working time after it is properly mixed and immediately placed onto the floor. Jobsite Temperature Approximate Floor Working Time Below 75 degrees Fahrenheit Approximately 25 to 30 minutes 75 degrees Fahrenheit Approximately 25 minutes 76 to 85 degrees Fahrenheit Approximately 22 to 25 minutes 85 to 90 degrees Fahrenheit Approximately 20 to 22 minutes Important: Working time begins becoming relevant only after the mixed epoxy is spread onto the floor. Do not use the published floor working time as permission to leave mixed 150FC sitting in the bucket. Higher temperatures shorten working time. Fast Cure and Topcoat Timing Under a full broadcast, 150FC cures in approximately 2 hours at 75 degrees Fahrenheit. At temperatures above approximately 90 degrees Fahrenheit, cure can occur in as little as approximately 75 minutes. Actual timing depends on material temperature, slab temperature, surrounding air temperature, humidity, film build, and jobsite conditions. Do not begin scraping or topcoating simply because a fixed amount of clock time has passed. Verify that the broadcast surface is hard enough for the next step. Built In Moisture Vapor Barrier Up to 12 lbs 150FC provides moisture vapor resistance up to 12 lbs within its published product limits. This can eliminate a separate moisture vapor barrier coat on qualifying full broadcast projects. The 12 lb rating does not eliminate the need to evaluate the concrete. Test the slab before installation and compare the result with the current product requirements. If moisture exceeds the 150FC limit or the slab presents another moisture condition outside its intended use, select a dedicated moisture vapor barrier from our Primers and Moisture Vapor Barriers. For help understanding slab moisture before coating, review our Moisture Testing Before Installing Epoxy Flooring Guide. Coverage Rates Coverage must match the role 150FC is performing in the flooring system. Do not stretch the epoxy farther simply to increase square foot coverage. Application Coverage Per Gallon Coverage Per 3 Gallon Kit Pigmented Full Flake Receiver Coat 133 to 150 square feet 399 to 450 square feet Primer on Porous Concrete 150 to 200 square feet 450 to 600 square feet Higher Build Approved Broadcast Application 100 to 135 square feet 300 to 405 square feet For most full flake receiver coat planning, use the 133 to 150 square foot per gallon range. The exact rate should match the complete system, concrete condition, required film build, and moisture requirements. Available Colors 150FC is currently available in the following options: Clear Black Light Gray Medium Gray Dark Gray White Tan For a full flake floor, select the appropriate pigmented receiver coat so any small gaps between flakes do not expose an unwanted background color. Concrete Preparation Fast cure epoxy does not compensate for poor concrete preparation. The slab must be clean, sound, mechanically opened, and ready to receive a high build resin. Remove existing coatings, curing compounds, sealers, adhesive, oil, grease, and other contaminants. Mechanically prepare concrete to approximately CSP 3. Vacuum the prepared floor thoroughly. Repair cracks, spalls, pits, and damaged concrete before coating. Test the slab for moisture before relying on the built in 12 lb moisture vapor rating. Contractor Tip: With 150FC, the entire job should be staged before mixing begins. Have the floor prepared, flakes or aggregate opened, squeegee and rollers ready, spiked shoes on, and the crew positioned before Part A and Part B are combined. Mixing 150FC 150FC uses a 2 parts Part A to 1 part Part B by volume mix ratio. Premix Part A. Thoroughly mix the pre-pigmented Base before adding the Activator. If separate pigment is being added, completely disperse it into Part A first. Add Part B. Pour the Activator directly into the center of the Base container. Avoid pouring Activator onto the sides of the Base container. Use the correct mixer. For a full 3 gallon kit, use only a Cage or Box style mixer. A paddle mixer does not move enough of this thick material through a full 3 gallon batch to ensure complete mixing. Mix according to material temperature. Mix for 2 full minutes at approximately 300 to 450 RPM when the material is above 75 degrees Fahrenheit. Mix for 3 full minutes when the material is below 75 degrees Fahrenheit. Partial batches. Measure exactly 2 parts Base to 1 part Activator by volume. A red paddle mixer may be used for partial batches. Mix only until the material is completely uniform. Smaller batches require less mixing time. Do not exceed 3 minutes. No induction time is required. Mix it and GET IT OUT OF THE BUCKET. Do not leave mixed 150FC sitting in the bucket. This fast cure 100% solids epoxy generates heat rapidly when the mixed material remains concentrated in mass. As soon as mixing is complete, immediately pour the epoxy onto the floor. Application Pour immediately. Pour mixed 150FC onto the prepared floor in long ribbons approximately 12 to 18 inches wide. Do not drain or scrape the bucket. Material remaining on the sides or bottom may not be mixed as completely as the main batch. Spread the epoxy. Use an appropriate notched rubber squeegee to spread the material at the required coverage rate. Roll and back roll. Use a quality 3/8 inch shed resistant epoxy roller cover to even the material and maintain consistent coverage. Do not continue back rolling after the epoxy begins to tack. Once 150FC starts to set, leave the material alone and continue the installation sequence. Broadcast immediately. Apply the vinyl flakes, quartz, sand, or approved aggregate while the epoxy is wet enough to completely receive the broadcast. Prepare for the topcoat. After the broadcast has cured sufficiently, scrape and vacuum the surface according to the flooring system requirements, then apply the specified topcoat. 150FC Technical Specifications Specification Published Value Product Type Fast cure two component 100% solids epoxy Solids by Volume 100% Mix Ratio 2 parts Part A to 1 part Part B by volume Mixed Kit Size 3 gallons Mixed Viscosity Approximately 900 cps Working Time at 75 Degrees Fahrenheit Approximately 25 minutes on the floor Full Broadcast Cure at 75 Degrees Fahrenheit Approximately 2 hours Full Broadcast Cure Above 90 Degrees Fahrenheit As little as approximately 75 minutes Recoat Window Approximately 4 to 24 hours when an additional resin coat is required Heavy Foot Traffic Approximately 48 hours Vehicle Traffic Approximately 72 hours Moisture Vapor Rating Up to 12 lbs within published product limits Shore D Hardness 89 to 91 Compressive Strength 16,500 psi Adhesion to Concrete 600 psi Tensile Strength 3,550 psi Flexural Modulus 4,700 psi Koenig Hardness 145 Taber Abrasion 22 mg loss VOC Less than 50 grams per liter Concrete Preparation Mechanical preparation to approximately CSP 3 Application Roller 3/8 inch shed resistant epoxy roller cover Topcoating a Full Broadcast Floor Once the 150FC receiver coat has cured and the full broadcast is ready, scrape the surface in multiple directions and vacuum thoroughly before topcoating. Poly Gloss 85 Polyaspartic is a common topcoat for One Stop Epoxy full flake flooring systems. Select the appropriate Poly Gloss 85 version based on floor size, temperature, working time, and installer experience. Browse our Vinyl Flakes when building a full flake broadcast system from individual components. Frequently Asked Questions What is 150 Fast Cure Epoxy used for? 150FC is designed for full broadcast flooring systems including full flake, quartz, sand, and other approved aggregate systems. It functions as the primer, receiver coat, and moisture vapor barrier within its published 12 lb moisture limit. Is 150FC good for one day garage floors? Yes. One day full flake garage floors are one of the primary applications for 150FC. The fast cure allows experienced crews to prepare the slab, apply the receiver coat, broadcast flakes, scrape, vacuum, and topcoat in the same day when jobsite conditions allow. Is 150FC beginner friendly? No. 150FC is intended for experienced epoxy installers. The faster cure requires good job planning, correct mixing, immediate placement, fast spreading, and controlled broadcast timing. How much working time does 150FC provide? Working time is approximately 25 minutes at 75 degrees Fahrenheit after the epoxy has been properly mixed and placed onto the floor. Cooler conditions generally provide more time. Higher temperatures shorten working time. How quickly can I topcoat a full flake floor? Under a full broadcast, 150FC cures in approximately 2 hours at 75 degrees Fahrenheit. In very warm conditions above approximately 90 degrees Fahrenheit, cure can occur in as little as approximately 75 minutes. Confirm that the broadcast is hard enough to scrape and vacuum before applying the topcoat. Does 150FC replace a moisture vapor barrier? 150FC can perform the moisture vapor barrier role on qualifying projects with moisture conditions within its published 12 lb limit. Test the concrete before installation. Slabs exceeding that limit or presenting other moisture conditions may require a dedicated moisture vapor barrier system. Can I use 150FC for a partial flake floor? No. A partial flake floor leaves a large portion of the epoxy exposed. 150FC is intended for full broadcast systems where the epoxy is completely buried beneath the broadcast media. Can I use 150FC for a solid color floor? No. Use a general purpose 100% solids epoxy such as One Stop Epoxy Self Leveling 100% Solids Epoxy when the epoxy itself will remain visible. Can I use 150FC as a metallic epoxy base coat? No. Use the appropriate slower curing pigmented epoxy base beneath a metallic flooring system. 150FC is reserved for full broadcast applications. Why does 150FC have to be completely covered? 150FC is not UV stable and can amber when exposed to light. Full flake, quartz, and sand broadcasts completely cover the epoxy before the clear topcoat is installed, preventing the epoxy color from remaining visible. Can 150FC be used outside? It may be used only as part of an appropriate full broadcast system where the 150FC is completely buried and is not the exposed finish. The complete exterior system must use a suitable UV resistant topcoat. How do I mix a full 3 gallon kit? Use only a Cage or Box style mixer. Mix at approximately 300 to 450 RPM for 2 full minutes when the material is above 75 degrees Fahrenheit and 3 full minutes when the material is below 75 degrees Fahrenheit. Then GET IT OUT OF THE BUCKET and onto the floor immediately. Can I add solvent to extend the working time? No. Do not add solvent to 150FC. Altering the formulation can affect cure, film build, and moisture vapor performance. How much 150FC do I need for a full flake floor? A typical pigmented full flake receiver coat is applied at approximately 133 to 150 square feet per gallon, giving approximately 399 to 450 square feet from one 3 gallon kit. Actual material requirements depend on the concrete profile, porosity, repairs, film build, and normal application loss. Technical Data and Safety Information Review the current product data and safety information before installation, particularly when 150FC is being used for moisture vapor control or in a commercial flooring system. View One Stop Epoxy TDS and SDS Sheets

16oz Measuring Cups (10PACK) Accurately measure epoxy with our 16oz measuring cups. Specifically designed for epoxy applications, these cups ensure precise and consistent mixing ratios, resulting in optimal performance of your epoxy projects. The clear markings in ounces and milliliters make it easy to achieve the perfect proportions. Resistant to epoxy chemicals and can be reused for multiple projects.

Malish Universal Clutch Plate complete with 5 SF Holders, Riser & Block 17" Swing buffer plate

17" Sanding Disc Screens – 10 Pack Upgrade your sanding projects with our 17" Sanding Disc Screens, designed for efficiency, durability, and professional results. This 10-pack of premium sanding discs is ideal for smoothing and prepping a variety of surfaces, ensuring flawless finishes every time. Key Features: High-Quality Material: Built to last, these sanding discs deliver consistent performance even on tough jobs. Versatile Application: Perfect for sanding wood, concrete, epoxy floors, and other surfaces. Precise Results: Achieve smooth, even finishes with minimal effort. Easy to Use: Designed for hassle-free attachment to standard 17" floor sanders. Cost-Effective 10 Pack: Get more done with a bulk pack of durable sanding screens. Whether you're a contractor working on large-scale projects or a DIY enthusiast tackling home improvements, these sanding disc screens offer the performance and reliability you need.

Slim Fit - Single S Segments - 15mm - Hard Bond 3 Pack – 18/20 Grit Maximize your grinding efficiency with Slim Fit Single S Segments, engineered to fit Lavina grinders and grinders using Lavina-compatible tooling. These premium diamond tools are perfect for smooth, precise grinding without gouging, offering exceptional production rates and extended tool life. Key Features: Lavina-Compatible Design: Specifically crafted for Lavina grinders and similar machines that use Lavina tooling. Hard Bond Diamond Tooling: Optimized for grinding soft, abrasive materials. 18/20 Grit Precision: Delivers consistent scratch patterns for surface preparation. Durable 15mm Segments: Ensures long-lasting performance and cost efficiency. Versatile Applications: Available in various grits and segment configurations to meet your project needs. Whether you're a contractor working with Lavina grinders or another compatible machine, the Slim Fit Single S Segments provide the precision and durability you need for superior surface preparation.  

2.5-Quart Epoxy Mixing Cups Achieve precise epoxy measurements and thorough mixing with our 2.5-quart mixing cups. Designed for larger projects, these 80-ounce cups provide clear measurement markings to ensure accurate proportioning every time. Their chemical-resistant construction makes them durable enough to withstand the demands of epoxy mixing, ensuring consistent results for all your applications. Key Features: Large Capacity: 2.5 quarts (80 ounces) ideal for mixing larger batches of epoxy. Accurate Measurements: Clear markings for precise ratio control and consistent results. Chemical-Resistant Material: Durable and reliable for all epoxy mixing needs. Convenient Design: Simplifies the mixing process for professional and DIY projects alike. Simplify your epoxy applications with these durable and efficient mixing cups, tailored to help you achieve flawless results every time.

Malish Universal Clutch Plate – 20" with 6 SF Holders, Riser & Block The Malish Universal Clutch Plate is the perfect solution for swing buffers, offering a reliable connection between your machine and attachments. Complete with 6 SF Holders, a riser, and a block, this 20" clutch plate is designed to provide optimal performance and versatility for a wide range of applications. Key Features: Universal Compatibility: Designed to fit most standard swing buffers. Complete Kit: Includes a riser, block, and 6 SF Holders for seamless attachment. Durable Construction: Built to withstand heavy-duty use in commercial and industrial environments. Optimized Performance: Ensures secure and efficient operation with various attachments. Whether you’re working on floor polishing, scrubbing, or sanding, the Malish Universal Clutch Plate delivers reliable performance and versatility to get the job done right.

24" Red Speed Squeegee – Flat, 1/8", 3/16", and 1/4" Notches This 24-inch notched speed squeegee is a must-have tool for installing epoxy floor coatings. Built with a heavy-duty metal frame and a durable red 1/8" neoprene rubber blade, this squeegee is ideal for spreading 100% solids epoxy base coats evenly across your surface. Whether you're installing in a garage, commercial space, or industrial setting, this tool makes the job easier and more precise. The red neoprene rubber blade is non-marking and designed for professional results, even for first-time installers. When the blade wears out, simply unscrew the frame and replace it—no need to buy an entirely new squeegee. Key Features: 24-Inch Width – Covers more area with each pass for faster installs Durable Red Rubber Blade – Built to last through multiple jobs Heavy-Duty Metal Frame – Strong and reusable; designed for contractor use Flat Blade Squeegee HD™         47150     24" Flat Red Rubber Blade               Use for Polyaspartic seal coat on a full flake floor (133 SFPG) and water base epoxy primers (160 – 200 SFPG) 1/8"   Notched Squeegee HD™ 47151    24" 1/8"  Red Rubber Blade (135 SFPG)                 3/16” Notched Squeegee HD™ 47152    24" 3/16" Red Rubber Blade (100 SFPG)           1/4"   Notched Squeegee HD™ 47153    24" Red Rubber Blade  (65 SFPG) How to Use: Pour your epoxy base coat (such as One Stop Epoxy 100% Solids Epoxy) in lines across the floor. Spread using the squeegee in a smooth, back-and-forth motion toward your finishing wall. Roll with a 3/8 inch epoxy roller to level and blend. Perfect For: Epoxy Garage floor coatings Full epoxy flake and quartz broadcast systems Commercial and industrial epoxy installations Complete your epoxy installation tool kit with this reliable, reusable squeegee. Don’t forget to check out our full line of epoxy installation tools and rollers.

3/8" Pro Performance Epoxy Roller Achieve professional-grade results with the 3/8"Pro Performance Epoxy Roller. This premium-quality roller is specifically designed for epoxy applications, providing smooth and even coverage across a variety of surfaces. Ideal for both large-scale and detailed projects, it ensures efficiency and precision with every stroke. Key Features: Optimized for Epoxy Coatings: Delivers consistent, flawless finishes for all epoxy applications. Versatile Performance: Perfect for use on a wide range of surfaces and project sizes. Premium Woven Material: Ensures smooth application without streaking or shedding. Efficient and Precise: Designed for fast coverage and professional-level accuracy. Size: Available in 18" & 9" Whether you're coating floors, countertops, or other surfaces, the 18" Pro Performance Epoxy Roller is a reliable choice for achieving exceptional results with ease.  Works best with this roller frame and handle.